Burst pipe repairs in Kensington 2033
A burst pipe in Kensington usually comes from age. Many Federation and interwar homes still have galvanised steel or early copper water pipe that has been patched over the decades, and in a terrace the line runs the full length of the house under the floor. Big street trees push roots under front gardens where the water service runs, and in the unit blocks along Anzac Parade a split flexi hose sends water straight into the unit below. We come up from Matraville, help you stop the water, and fix the pipe properly.
Stop the water first
- Turn off the water at the isolating valve near the fixture, or at the meter, usually near the front boundary. In a unit block, your meter or valve may be in a bank near the entry or in a cupboard.
- Turn off the power at the switchboard if water is near power points, lights or appliances.
- Tell the neighbour below or next door if water could reach them.
- Move belongings out of the way and put down towels or buckets.
- Call us and tell us what you can see.
Burst pipe jobs we do in Kensington
Galvanised pipe bursts
Rusted steel pipe cut out and replaced with copper.
Bursts under the floor
Long lines under terraces found and repaired.
Flexi hose bursts
Split hoses under sinks, basins and toilets replaced.
Water service bursts
Broken pipe between the meter and the house repaired or replaced.
Bursts in walls
Pipes in brick and rendered walls found and fixed.
Hot water bursts
Failed valves and pipes at the hot water system repaired.
How a burst shows up
- Water spraying or pouring from a pipe, hose or fitting.
- Water coming through a ceiling or down a wall.
- A sudden drop in water pressure.
- The sound of rushing water under the floor or in a wall.
- A wet patch in the front garden or water bubbling up through paving.
- The meter spinning with every tap off.
Why pipes burst in Kensington
Galvanised pipe rusting through
Galvanised steel pipe rusts from the inside over decades. The pipe wall gets thinner, especially at threaded joints, until it gives way. Often it starts as a pinhole leak, but under pressure a weak spot can split open.
Old repairs
In homes this age, the pipes have usually been repaired before. A mix of galvanised, copper and plastic, joined with different fittings, gives plenty of weak points, especially where different metals meet.
Flexi hoses
Braided flexi hoses connect most taps, toilets and dishwashers. As they age, the braid rusts and the rubber inside perishes. When one fails, it can let out a lot of water quickly.
Roots and big trees
Kensington's big trees send roots under front gardens and paths, where the water service runs. Roots can crack an old pipe, and ground movement can pull a joint apart.
High water pressure
High pressure is hard on old pipe, joints and hoses. A home that's had several leaks or bursts may need a pressure limiting valve.
Kensington homes and where bursts happen
| Home type | Typical pipes | Where bursts happen |
|---|---|---|
| Terraces and semis | Long line from the meter to the back | Under the floor, in back extensions |
| Federation and interwar houses | Galvanised or early copper | Threaded joints, walls, the water service |
| Older unit blocks | Mixed old and newer pipe, shared risers | Flexi hoses, pipes in walls and ceilings |
| Newer apartments | Copper or plastic, flexi hoses | Flexi hoses, fittings behind vanities |
| Homes under big trees | Old water service under the garden | Cracked pipe, pulled joints |
How we repair a burst
- Make sure the water is off and the area is safe.
- Find the burst, using leak detection equipment if it's hidden.
- Check the pipe either side to see if the damage goes further.
- Give you options, each with a fixed price, before any repair starts.
- Repair it: cut out the damaged section and join in new pipe.
- Turn the water back on, test for leaks and check every tap.
Repair or replace?
| Situation | Usual fix |
|---|---|
| One damaged section in sound pipe | Cut out and replace the section |
| Galvanised pipe rusted along the run | Replace the run with copper |
| Split flexi hose | Replace the hose, and check the others |
| Broken water service | Repair the section or replace the service |
| Burst in a wall that's hard to reach | Repair through a small opening, or reroute |
| Repeated bursts | Check the pressure and the condition of the whole system |
What affects the cost
- Where the burst is: under a floor, in a wall, in the garden or under paving.
- How much pipe needs replacing.
- Access under floors, in tight terraces and in unit blocks.
- Extra work, such as a pressure limiting valve.
- Making good, such as patching a wall.
You get a fixed price for each option before any repair starts.
Who's responsible?
- You: pipes and fixtures on your side of the meter, and the fixtures inside your unit.
- Owners corporation: shared pipes and risers in a block of units.
- Sydney Water: the water main and the meter.
Signs it's urgent and when it can wait
- Call straight away if water is pouring out, coming through a ceiling or near electrics.
- Call soon if there's a wet patch in the garden, a drop in pressure or the meter is moving.
- Book a time if you'd like old pipe or flexi hoses checked before they fail.
A recent burst repair nearby
Here's a recent burst repair nearby in Matraville, where a damaged copper water service was repaired without replacing the whole line.
Copper water service repaired after crane damage, Matraville (nearby)
The problem: while a pool was being craned into the property next door, the copper water service buried under a Matraville backyard was damaged.
What we did: by the time we arrived the pipe was dug out and the water was off. Only the section under the lawn beside the paving was damaged, and the rest of the copper was in good order, so we cut out the damaged length and joined in new copper with new fittings.
The result: the water was back on in under an hour, every tap ran properly, and there was no need to replace the whole service.


More local work is on our recent projects page.
“Great plumber, fixed my leaking taps quickly and at a great price!”
Tom (Google review)
Bursts across Kensington
- Along Anzac Parade and the light rail: unit blocks where a burst floods the unit below.
- Towards Moore Park and Centennial Park: Federation and interwar houses with galvanised pipe.
- On the side streets: terraces and semis with long lines under the floor.
- Near UNSW: shared houses with heavily used bathrooms and hoses.
- Under the big street trees: water services cracked by roots.
Galvanised pipe: when to replace it
If your home has had one burst in galvanised pipe, it's likely the rest of the run is in similar condition. Repairing one section stops the water today, but the next weak joint may not be far away. When we repair a burst in galvanised pipe, we look at the pipe either side and tell you what we see. If it's badly rusted, we'll give you the option of replacing the run with copper, with a fixed price, so you can decide whether to do it now or later. See our galvanised pipes guide.
Bursts under the floor of a terrace
In a terrace or semi, the water line often runs under the floor from the meter at the front to the kitchen, bathroom and laundry at the back. A burst under there can soak the subfloor before you know it. Signs are the sound of running water, a sudden drop in pressure at the back taps or the meter spinning. We get under the house, find the burst and repair it. If the line is old along its whole length, we can run a new one along the side of the house where it's easier to reach.
Bursts in units: protecting the unit below
In a unit, a burst flexi hose, pipe or fitting sends water straight down. Turn off the water at your isolation valve or meter, and tell the neighbour below straight away. If water is coming through your ceiling from upstairs, ask them to turn their water off, keep out from under any bulging ceiling and turn off the power to that area if it's safe. We fix the burst, and if it's in a shared pipe or riser, we give you a note to pass on to the owners corporation.
Flexi hoses: the most common burst
Flexi hoses under sinks, basins and toilets are the most common cause of bursts we see in units. They look fine until they fail. Signs of trouble are rust spots on the braid, bulges, kinks and damp at the fittings. If one has burst, the others in your home are likely the same age, so it's worth replacing them all at once.
Water services under big trees
The water service runs underground from the meter to the house. In Kensington, it often runs under a front garden with a big tree, a path or a driveway. Roots can crack an old pipe or push it out of line, and over the years ground movement can pull a joint apart. A burst here shows as a wet patch, water bubbling up or a sudden drop in pressure. We dig to the burst, repair it and check the rest of the service. If it's old galvanised pipe, replacing it may be the better option.
Drying out after a burst
After a burst, floors, walls and ceilings need to dry out properly to prevent mould and damage. Open windows, run fans and remove wet rugs and furniture. For large amounts of water, a drying specialist may be needed. Don't paint or close up walls until they're dry.
Going away?
If you're going away for more than a few days, turning off the water at the meter is a simple way to protect your home from a burst while nobody's there.
A twice-yearly pipe check
- Look under sinks and basins for rust, bulges or damp on flexi hoses.
- Check the meter with every tap off.
- Look for wet patches in the garden or under the house.
- Check the hot water system for drips or puddles.
- Know where your meter and isolation valves are.
Bursts at the hot water system
A burst at the hot water system can be a failed valve, a pipe joint or the tank itself. In Kensington, hot water is often in a tight laundry or a side passage, so a leak can go unnoticed. Turn off the cold supply to the system and the power or gas, then call us. See hot water in Kensington.
Our written report for insurance
If you're making an insurance claim, we can give you a written report with the cause of the burst, what we repaired and photos.
Rerouting instead of opening walls
When a pipe in a wall or under a floor bursts and is hard to reach, it's sometimes better to run a new pipe along a different route than to open up the wall or floor. We'll give you both options with a fixed price for each.
Small leaks that turn into bursts
A pinhole leak in old pipe, a weeping joint or a drip from a flexi hose is often the warning before a burst. If you notice one, have it looked at. Fixing it early is easier than dealing with a burst.
How we work in your home
We arrive in the window we agreed, put down protective mats, find the burst and explain what we see. You get options and a fixed price before any repair starts. We fix it, test it and clean up before we leave.
Time to replace the old pipe?
If your home has had several leaks or bursts, weak flow, rusty water or a mix of old repairs, it may be time to replace the old pipe. We'll look at the system, tell you which parts are worth keeping and which aren't, and give you a fixed price.
Corrosion you can see
Where pipes are exposed, under the house, along the side or in the laundry, look for rust, white or green crusting at joints and damp spots. These are signs of corrosion, and the pipe may be weaker than it looks.
Older pipes and water quality
Rusty or discoloured water, especially first thing in the morning, can be a sign of old galvanised pipe rusting inside. It's another reason to consider replacing it.
Units and owners corporations
In a unit block, the pipes inside your unit are generally yours, while shared risers and mains are usually the owners corporation's. If a burst is in a shared pipe, we make it safe and give you a note with what we found so you can pass it on.
Choosing new pipe
For water pipes, we mostly use copper, which is durable and suits most homes. In some situations, other approved pipe materials make sense. We'll explain the options for your home.
Shared houses near UNSW
Shared houses near UNSW have bathrooms, laundries and kitchens that get used hard, and flexi hoses and fittings wear faster. A quick check of hoses and fittings each year helps prevent bursts.
Why Kensington homeowners call us
We come up from Matraville and know the old pipe in Kensington's terraces, Federation homes and unit blocks. We fix bursts properly, check the pipe either side and give you a fixed price before any repair starts. Our workmanship carries a lifetime labour warranty.
What's in your walls?
In older homes, pipes in walls can be galvanised, copper or a mix, depending on past repairs. If we open a wall to fix a burst, we'll tell you what we find and whether the rest of the pipe looks sound.
After the repair
We turn the water back on slowly, test for leaks and check every tap. Air in the pipes may make the taps splutter briefly. If the water is discoloured, run the cold tap for a few minutes.
Small jobs that prevent bursts
- Replace old flexi hoses.
- Fit a pressure limiting valve if the pressure is high.
- Replace badly corroded sections of exposed pipe.
- Fit isolating valves under sinks and basins.
Re-piping an older home
Replacing old galvanised pipe throughout a Kensington home is a bigger job, but it ends the cycle of leaks and bursts and usually improves the flow at every tap. We plan the route to keep disruption low, often running new pipe under the floor or along the side of the house. You get a fixed price before we start.
Bursts in back extensions
Many Kensington terraces have a kitchen, laundry or bathroom in a back extension added years after the house was built. The water pipe to the extension was often joined onto the original line, sometimes with a different material, and run through a tight space under the floor or in a wall. Those joins are common burst points. When we repair one, we check how the extension's pipe connects to the rest of the house and whether the join is likely to fail again.
Knocked and damaged pipes
Not every burst comes from age. A pipe can be damaged by a nail or screw through a wall, a spade in the garden, a fence post or work on the house next door, as in the Matraville job above. If you know the pipe was damaged, turn the water off and call us. We'll repair the damaged section and check the rest of the line so you're not left with a hidden weak spot.
Water hammer and bursts
If your pipes bang when a tap is turned off or the washing machine stops filling, that's water hammer. Each bang is a pressure spike that shakes the pipes and strains the joints. Over time it can loosen fittings and contribute to leaks and bursts, especially in old pipe. A pressure limiting valve or a water hammer arrestor reduces the spikes, and securing loose pipes under the house stops them moving.
Know where your meter is
In a burst, the first thing you need is the meter or main valve. In most Kensington houses, the meter is near the front boundary, sometimes hidden by a hedge or in a small pit. In unit blocks, meters are usually in a bank near the entry or in a meter room. Find yours now, check the valve turns, and make sure everyone in the house knows where it is.
Burst pipe words explained
- Isolating valve: a small valve that turns off the water to one fixture.
- Water meter: the meter near the front boundary that also has a shut-off valve.
- Water service: the pipe from the meter to the house.
- Galvanised pipe: old steel water pipe that rusts from the inside.
- Flexi hose: a braided hose connecting a tap or toilet to the pipe.
- Riser: a pipe that carries water up through a building.
- Pressure limiting valve: a valve that reduces water pressure in the home.
What happens when you call
Tell us what's going on
Call or send a quick form. A photo of the problem helps us come prepared. No call-out fee.
Options and a fixed price first
We find the cause, explain your options and give you a fixed price for each before any work starts.
Fixed, tested and backed
We do the work, test it, clean up, and back our workmanship with a lifetime labour warranty.
Why Kensington homeowners call us
- Based in Matraville, a short drive from Matraville
- Rated 5.0 from 110 Google reviews
- Free quotes, with options and a fixed price before any work starts
- Lifetime labour warranty on our workmanship
- Licensed plumbers, drainers and gasfitters (Lic. 398171C)
Burst pipe questions from Kensington homeowners
What should I do first?
Turn the water off at your isolating valve or meter, tell the neighbour below, then call us.
Where is my meter in a block of units?
Usually in a bank near the entrance. Look for your unit number.
Water is coming through my ceiling from upstairs. What do I do?
Ask your neighbour to turn their water off, keep out from under a bulging ceiling, and call us.
My galvanised pipe burst. Should I replace the rest?
It depends on its condition. We'll check the pipe either side and give you options.
My flexi hose burst. Should I replace the others?
Yes. They're likely the same age and condition.
There's a wet patch in my front garden. Is it a burst?
It could be the water service. The meter test will tell you.
Can you find a burst under the floor?
Yes. We get under the house and use leak detection equipment if needed.
Will you have to cut my wall?
Sometimes, through a small opening. We may be able to reroute instead.
Can you give me a report for insurance?
Yes, with the cause, the repair and photos.
How long does a repair take?
Most section repairs take an hour or two.
Can high pressure cause bursts?
Yes. A pressure limiting valve helps.
What warranty do I get?
Our workmanship carries a lifetime labour warranty.
More plumbing in Kensington: our Kensington plumber page, leak detection, hot water and taps and toilets. Nearby: burst pipes in Randwick and Coogee. Guides: galvanised pipes, hidden water leaks and water meter guide.