Burst pipe repairs in Hillsdale 2036
A burst pipe is one of the most stressful things that can happen at home. In Hillsdale, many cottages still have water pipes from when the suburb was built after the war, and the walk-up unit blocks have pipes running through walls and ceilings shared with the neighbours. When a pipe gives way, water can spread quickly, under the floor, through the ceiling below, or across the front yard. We're around the corner in Matraville, so we can get to Hillsdale quickly, stop the damage and repair the pipe properly.
Stop the water first
- Turn off the water at the meter. In a cottage, it's usually near the front boundary. In a unit block, meters are often in a bank near the front or in a cupboard; look for your unit number.
- Turn off the power to any area where water is near electrics, at the switchboard.
- Open a tap at the lowest point to drain pressure from the pipes.
- Move valuables and lay towels to protect floors.
- Tell the unit below if you're in a block and water is coming through the floor.
- Call us and tell us what you can see.
If you can't find or turn the meter valve, let us know when you call and we'll talk you through it.
Burst pipe jobs we do
Galvanised pipe replacement
Rusted galvanised replaced with copper or modern approved pipe, in stages or all at once.
Water service repairs
Burst services found and repaired in sandy front yards.
Water service replacement
Old services replaced with new pipe properly bedded in sand.
Under-floor repairs
Bursts under cottages repaired from the subfloor.
Wall and ceiling repairs
Bursts in unit walls and ceilings repaired, or pipes rerouted.
Hoses and stop taps
Failed hoses and seized stop taps replaced.
How a burst shows up
- Water spraying or pouring from a pipe, wall or ceiling.
- A wet patch on a ceiling, especially in a unit below a bathroom or kitchen.
- A soggy patch in the front yard or along the side path.
- Water under the house or the sound of running water under the floor.
- A sudden drop in water pressure at every tap.
- The meter spinning with every tap off.
- A much higher water bill than usual.
Why pipes burst in Hillsdale
Galvanised steel
Many of Hillsdale's post-war homes were plumbed with galvanised steel water pipe. It rusts from the inside, narrowing the bore and thinning the wall until it gives way, usually at a thread or joint. If your home still has galvanised pipe, bursts become more likely each year. See galvanised pipes.
Copper under the floor
Copper pipe is long-lasting, but it can split where it's been bent too tightly, where it rubs against a bearer or joist, or where it was joined to galvanised without the right fitting. Under a timber floor, a small split can run for weeks before anyone notices.
Sandy ground and water services
The water service runs from the meter to the house, usually under the front yard. In Hillsdale's sandy soil, older services can shift and crack, and roots can crush them. Copper services can also corrode where they touch other metals or where the sand around them stays wet.
Water pressure
Mains pressure varies across the area and can be high at some times of day. High pressure puts strain on every joint and fitting. A pressure limiting valve after the meter reduces that strain.
Building work and digging
Bursts often happen when someone digs in the wrong place: a fence post, a new garden bed, a footing, or machinery next door. Knowing where your water service runs helps avoid that.
Hillsdale homes and where bursts happen
| Home type | Typical pipes | Common burst points |
|---|---|---|
| Three-storey unit blocks | Copper and some galvanised in walls and ceilings, shared risers | Bathroom and kitchen walls, ceilings above units below |
| Post-war cottages | Galvanised or copper under timber floors | Threads and joints under the floor, hot water connections |
| Former Housing Commission homes | Original galvanised with some copper repairs | Joins between old and new pipe |
| Newer homes and units near Southpoint | Copper or modern plastic pipe | Fittings, hoses, nail and screw damage |
How we repair a burst
- Make it safe: water off, and check for any electrical risk.
- Find the burst, using a camera or leak detection gear if it's hidden.
- Check the pipe either side of the burst to see its condition.
- Give you options: repair the section, replace a longer run, or reroute.
- Repair or replace with copper or modern approved pipe and fittings.
- Pressure test and check every tap and fitting.
- Write a short report with photos for insurance if you need it.
Repair or replace?
| Situation | Usually a repair | Usually a replacement |
|---|---|---|
| One split in sound copper | Cut out and join in new copper | Not needed |
| Galvanised burst at a joint | Short-term repair possible | Replace the run, as more bursts are likely |
| Water service cracked in one spot | Repair the section | Replace if old and failing elsewhere |
| Pipe in a wall | Repair through a small opening | Reroute if the run is poor |
| Several bursts in a year | Not recommended | Replace the pipe system |
What affects the cost
- Where the burst is: in the open, under a floor, in a wall or under paving.
- The pipe material and its condition.
- How much needs replacing.
- Access: crawl space height, wall finishes and furniture.
- Making good: patching walls, tiles or paving.
You get a fixed price for each option before any repair starts.
Who's responsible?
- You: pipes from the meter to your home and inside it.
- Owners corporation: shared risers and pipes in common areas of a block.
- Sydney Water: the main and the pipe to and including the meter.
If water is leaking on the street side of the meter, report it to Sydney Water.
Signs it's urgent and when it can wait
- Call straight away if water is spraying, pouring through a ceiling, near electrics, or you can't turn it off.
- Call soon if there's a wet patch growing, a soggy front yard, or the meter is moving with taps off.
- Book a time if you've had a repair and want the old galvanised replaced before the next burst.
A recent burst repair nearby
Here's a recent burst repair nearby in Matraville.
Copper water service repaired after crane damage, Matraville (nearby)
The problem: while a pool was being craned into the property next door, the copper water service buried under a Matraville backyard was damaged.
What we did: by the time we arrived the pipe was dug out and the water was off. Only the section under the lawn beside the paving was damaged, and the rest of the copper was in good order, so we cut out the damaged length and joined in new copper with new fittings.
The result: the water was back on in under an hour, every tap ran properly, and there was no need to replace the whole service.


“Great plumber, fixed my leaking taps quickly and at a great price!”
Tom (Google review)
More local work is on our recent projects page.
Bursts across Hillsdale, street by street
- Unsted Crescent and the unit streets: bursts in walls and ceilings of walk-up blocks.
- Rhodes Street and the cottage streets: galvanised and copper under timber floors.
- Along Bunnerong Road: water services under busy front yards near Southpoint.
- Near Wentworth Avenue: services crushed by tree roots on the Eastgardens side.
- Towards Matraville: older cottages with original services in sand.
Bursts in units: protecting the home below
In a Hillsdale walk-up, the pipes in your bathroom and kitchen often run in the floor or the wall above the unit below. A burst can reach their ceiling within minutes. Turn off your water, tell your neighbour, and call us. We'll find the burst, repair it, and check the ceiling below for water. We'll also give you a short written report with photos, which helps if insurance is involved or if the owners corporation needs to know. If the burst is on a shared riser, we'll explain what we found and what needs to happen next.
Drying out a cottage
When a pipe bursts under a timber floor, water can pool in the subfloor and soak the bearers and joists. After the repair, open the subfloor vents, keep air moving, and check for standing water. If the floor feels soft or there's a musty smell after a few weeks, have it looked at. Drying out properly helps avoid rot and other problems later.
Time to replace the galvanised?
If your Hillsdale home has had one galvanised burst, more are likely. The rest of the pipe is the same age and in similar condition. Replacing it all at once, or in stages starting with the worst sections, ends the cycle of bursts and repairs and usually improves water pressure too. We can camera or inspect the pipes, show you their condition, and give you options with fixed prices.
Going away?
- Turn off the water at the meter if you'll be away for more than a few days.
- Turn off the washing machine taps.
- Ask a neighbour to check for wet patches or water noises.
- Know where your meter is before you need it.
A twice-yearly pipe check
- Read the meter with every tap off, then again an hour later. Any movement points to a leak.
- Look under sinks and behind toilets for damp or rusty hoses.
- Check the hot water system for drips at valves and connections.
- Walk the front yard for soggy patches along the water service.
- Look up at ceilings for new stains.
See our water meter guide.
Bursts at the hot water system
Hot water connections are a common burst point, especially on older systems with galvanised fittings or old flexible connectors. The relief valve may also drip or discharge if pressure is too high. If water is coming from around your hot water system, turn off the cold water valve to the system and call us. See hot water in Hillsdale.
Our written report for insurance
If you're making an insurance claim, a clear report helps. We note the cause of the burst, where it was, what we repaired, and include photos before and after. We can't tell you what your policy covers, but we can give you the facts your insurer will ask for.
Garden and courtyard taps
Outdoor taps and the pipes that feed them are exposed to sun, knocks and garden work. Old galvanised risers to garden taps rust through at ground level, and hoses left connected under pressure can burst. Check outdoor taps when you check the rest, and replace rusty risers before they fail.
Rerouting instead of digging
Sometimes a pipe runs under a slab, a tiled floor or a concrete path, and repairing it in place would mean breaking up a lot of finished surface. In those cases, we can often run a new pipe by a different route, through the subfloor, the ceiling space or along an outside wall, and disconnect the old one. We'll explain the options and the fixed price for each.
What's in your walls?
Most Hillsdale homes have water pipes hidden in walls, floors and ceilings. In cottages, pipes usually run under the timber floor and come up through the floor to each fixture, which makes them easier to reach from the subfloor. In unit blocks built with brick and concrete, pipes are often chased into the brick walls or run in the ceiling space of the unit below, which makes bursts harder to reach. Knowing roughly where your pipes run helps you spot the early signs of trouble, like a damp patch at skirting level or a bubbling paint finish, and helps us plan the repair.
If you're putting up shelves, hanging a TV or fixing anything to a bathroom or kitchen wall, check for pipes first. A screw or nail through a pipe is a common cause of slow leaks that turn into bursts. If it happens, leave the screw in place, turn off the water and call us.
Small leaks that turn into bursts
Many bursts start as small leaks. A pinhole in galvanised pipe, a weeping joint, or a fitting that drips slowly can go on for weeks before the pipe gives way completely. Under a floor or in a wall, nobody sees it until the damage is done. A rising water bill, a meter that moves with every tap off, a musty smell or a damp patch are all signs worth acting on. Finding a small leak early is far cheaper and less disruptive than repairing a burst and drying out the damage. See leak detection in Hillsdale and our hidden water leak guide.
Older pipes and water quality
Old galvanised pipe doesn't just burst. As it rusts inside, it can give you brown water when you first turn on a tap, low pressure at some fixtures, and flecks of rust in aerators and washing machine filters. If you're noticing these, the pipe is near the end of its life. Replacing it improves pressure and water quality as well as removing the burst risk. We'll explain which runs are the worst and where to start if you'd like to do it in stages.
How we work in your home
When we arrive for a burst, the first job is to make sure the water is off and the area is safe. Then we find the burst and check the pipe around it, so we're not repairing one spot only for the pipe to fail a few centimetres away. We protect floors and furniture, keep the work area tidy, and explain what we've found before we start any repair beyond making it safe. Once the repair is done, we turn the water back on slowly, bleed air from the pipes, check every tap and fitting, and make sure there are no leaks. We'll tell you about anything else we noticed that's close to failing, so you can decide whether to deal with it now or later.
Units, owners corporations and insurance
Burst pipes in unit blocks can involve several parties: you as the owner of the unit, the owners corporation for shared pipes and common property, your neighbours whose homes may be affected, and insurers for each. It helps to have clear facts. We'll tell you where the burst was, whether the pipe is inside your unit or shared, what caused it if we can tell, and what we did. The written report and photos give everyone the same information, which helps decisions get made quickly.
If the burst is on a shared pipe, we can make it safe and do a temporary repair so you have water, then provide the report so the owners corporation can arrange the permanent work.
Water services in sandy front yards
In most Hillsdale cottages, the water service runs from the meter at the front boundary, under the front yard, to the house. In sand, a burst service doesn't always show up as a puddle. Water can drain straight down and away, so the first sign may be a lush green strip in the lawn, a sinking paver, low pressure or a high bill. We confirm the leak at the meter, then trace the line to find the burst. Once it's exposed, we check the pipe either side. If the service is old copper or galvanised and the camera or the exposed pipe shows it's in poor condition, replacing the whole service is often the better long-term choice. New pipe is laid on clean sand and covered properly so it's protected from movement and sharp objects.
Pipes near trees
Tree roots grow towards water, and a slow leak from a water service can draw them in. Over time, roots can wrap around a pipe and crush it, or lift and crack it as they thicken. If your water service runs near a large tree, it's worth knowing where the line is and keeping an eye on the meter. When we replace a service near a tree, we route it away from the roots where we can.
Choosing new pipe
When a section of pipe needs replacing, we use copper or a modern approved pipe system, depending on where it runs and what suits your home. Both last for decades when installed properly. We'll explain the choice and why we recommend it for your job, and the fixed price for each option.
Whatever the burst, our aim is the same: stop the damage, fix the pipe properly, and leave you with a clear picture of the rest of your plumbing so you can plan ahead.
If you're not sure whether you have galvanised pipe, look where the pipe comes out of the wall under a sink or at the hot water system. Galvanised is dull grey steel with threaded joints; copper is reddish-brown with soldered or pressed fittings. Send us a photo and we'll tell you what you've got.
Burst pipe words explained
- Water service: the pipe from the meter to the house.
- Galvanised pipe: steel pipe coated with zinc, used in older homes.
- Riser: a vertical pipe carrying water up through a building.
- Pressure limiting valve: a valve that keeps mains pressure at a safe level.
- Stop tap: a small valve that turns off water to one fixture.
- Pressure test: a check that the repaired pipe holds pressure without leaking.
What happens when you call
Tell us what's going on
Call or send a quick form. A photo of the problem helps us come prepared. No call-out fee.
Options and a fixed price first
We find the cause, explain your options and give you a fixed price for each before any work starts.
Fixed, tested and backed
We do the work, test it, clean up, and back our workmanship with a lifetime labour warranty.
Why Hillsdale homeowners call us
- Based in Matraville, around the corner from Hillsdale
- Rated 5.0 from 110 Google reviews
- Free quotes, with options and a fixed price before any work starts
- Lifetime labour warranty on our workmanship
- Licensed plumbers, drainers and gasfitters (Lic. 398171C)
Burst pipe questions from Hillsdale homeowners
What should I do first?
Turn the water off at the meter, then call us.
Where is my meter in a unit block?
Usually in a bank near the front of the block or in a cupboard. Look for your unit number.
Can you find a burst under the floor or in a wall?
Yes, with leak detection gear and a camera where needed.
Will you have to cut my wall?
Sometimes, through a small opening. We may be able to reroute instead.
My galvanised pipe burst. Should I replace it all?
Usually yes, or in stages, because more bursts are likely.
Who pays if a riser bursts in my block?
Shared risers are usually the owners corporation's.
Can you give me a report for insurance?
Yes, with the cause, the repair and photos.
Why did my water pressure drop suddenly?
Often a burst. Check the meter with taps off.
Can you repair the water service in my front yard?
Yes, and replace it if it's old and failing.
How long does a repair take?
Most section repairs take an hour or two.
Can high pressure cause bursts?
Yes. A pressure limiting valve helps.
What warranty do I get?
Our workmanship carries a lifetime labour warranty.
More plumbing in Hillsdale: our Hillsdale plumber page, leak detection, hot water, taps and toilets and blocked drains. Nearby: burst pipes in Pagewood and Matraville. Guides: galvanised pipes, hidden water leaks and water meter guide.