★★★★★ 5.0 from 100+ Google reviews · Your Sydney Plumber

Gas fitting in Chifley 2036

Our licensed gasfitters look after gas in Chifley homes, townhouses and units: cooktop and oven connections, heater bayonets, gas storage and continuous flow hot water, outdoor BBQ points, gas leak checks and capping off old points. Every job is pressure tested and certified, and you get options and a fixed price before any work starts. We're a few minutes away in Matraville, and our workmanship carries a lifetime labour warranty.

Gas is part of daily life in plenty of Chifley homes: the cooktop, the hot water, a heater on a winter night, or a BBQ on the back deck. In the older cottages, gas lines may be decades old and were never designed for today's appliances. In the larger family homes that have replaced many of them, gas often runs to several continuous flow units, an outdoor kitchen and a cooktop all at once. Either way, gas work has to be done by a licensed gasfitter and done properly. We're a few minutes away in Matraville.

Gas work we do in Chifley

Cooktops and ovens

New cooktops and ovens connected, or old ones swapped, with approved fittings and a pressure test.

Heater bayonets

Bayonets added or moved so a portable heater can sit where you need it.

Gas hot water

Storage and continuous flow units connected or replaced, with the supply sized for them.

Outdoor BBQ points

Fixed gas points run to decks and alfresco areas for a natural gas BBQ.

Leak checks

The whole system pressure tested to confirm it's sound.

Capping off

Old points capped and tested when appliances go electric.

Signs you need a gasfitter

  • A gas smell near an appliance, the meter or outside.
  • Yellow or orange flames on the cooktop instead of blue.
  • Soot around a heater or hot water flue.
  • Hot water goes cold when the cooktop or heater is on.
  • A burner won't light or keeps going out.
  • An error code on a continuous flow unit.
  • A new appliance needs connecting.
  • A higher gas bill with no change in use.

Why gas jobs come up in Chifley

Older gas lines in cottages

Chifley's older cottages were built over many years, and their gas lines were added and extended as needs changed. Many run under timber floors or along outside walls in older pipe, sized for a stove and maybe a storage hot water tank. When a new cooktop, heater or continuous flow unit is added, the old line may not carry enough gas, and appliances underperform.

New homes with high gas demand

The larger family homes that have replaced many Chifley cottages often have two continuous flow units, a large cooktop, ducted heating or several heater points, and an outdoor BBQ point. Together, they can draw a lot of gas at once. If the meter, regulator or pipe sizes weren't planned for that, appliances can starve each other: the shower goes cold when the cooktop is on, or the BBQ flames drop when the heating runs.

Townhouses and duplexes

Townhouses and duplexes usually have separate meters and lines for each home. Space is tight, so continuous flow units sit on walls near windows and boundaries, where flue clearances matter.

Units in the 1960s blocks

Units in Chifley's older four- and five-storey blocks may have gas cooktops fed from a bank of meters, with lines running through common areas. Work on your own appliances is yours to arrange; shared lines are the owners corporation's.

Chifley homes and their gas

Home typeTypical gas set-upCommon jobs
Older cottagesOlder lines under floors, cooktop, storage hot water, heater pointsLine upgrades, cooktop swaps, heater bayonets, leak checks
New family homesLarge meters, continuous flow, cooktop, BBQ point, heatingError codes, gas supply sizing, BBQ points
Townhouses and duplexesSeparate meters, wall-mounted continuous flowUnit replacements, flue clearances
1960s unit blocksMeter banks, cooktopsCooktop swaps, capping off, leak checks

How a gas job runs

  1. Talk it through: what you want connected, moved, fixed or capped.
  2. Check the supply: meter, regulator and pipe sizes.
  3. Give you options with a fixed price for each, before any work starts.
  4. Do the work with approved pipe and fittings.
  5. Pressure test the system to confirm there are no leaks.
  6. Commission the appliance and check the flame and operation.
  7. Lodge the certificate of compliance as required in NSW.

Repair, extend or new line?

SituationUsually best
Swapping a cooktop on an existing pointConnect the new cooktop and test
Adding a heater bayonet near an existing lineExtend the line
Adding continuous flow to an older homeCheck the supply, likely upsize the line or regulator
Several appliances starving each otherResize the supply to suit the total load
Old line leaking under the floorRepair or replace the section
Going electricCap and test the old points

What affects the cost

  • The type of job: connection, new point, new line or repair.
  • The distance from the meter or existing line.
  • Access: under floors, through walls, in tight spaces.
  • Whether the supply needs upsizing.
  • The appliance and its connection requirements.

You get a fixed price for each option before any work starts.

Who's responsible?

  • You: gas pipes and appliances on your side of the meter.
  • Owners corporation: shared gas lines in a unit block or townhouse complex.
  • Your gas network: the meter and the supply up to it.

Safety checks you can do

  1. Know where your meter is and how to turn it off.
  2. Look at your cooktop flames: blue with a small steady tip.
  3. Check for soot around heaters and the hot water flue.
  4. Keep vents and the area around the hot water unit clear.
  5. If a smell comes and goes, note when and where, and call us.

Signs it's urgent and when it can wait

  • Act straight away if the gas smell is strong: turn off at the meter, get out, call Jemena, then us.
  • Call soon if there's a faint smell, yellow flames, soot or no hot water.
  • Book a time if you're planning a new cooktop, heater point, BBQ point or hot water change.

A recent gas job nearby

Here's a recent gas hot water job nearby in Maroubra, where the gas supply had to be upgraded for the new unit.

Old gas tank replaced with continuous flow, Maroubra (nearby)

The problem: the gas storage tank down the side of a Maroubra home had stopped sending hot water to the taps.

What we did: we explained repair against replacement and the systems that would suit, and the owners chose a Rinnai continuous flow unit. We removed the old tank, mounted the new unit on the wall, upsized the copper pipework, and replaced the gas regulator at the meter so the new system gets enough gas.

The result: reliable hot water at every tap, on a gas supply sized for the new unit.

Old gas hot water tank before replacement near Chifley
The old tank, Maroubra
New continuous flow gas hot water unit near Chifley
The new continuous flow unit

“Great plumber, fixed my leaking taps quickly and at a great price!”

Tom (Google review)

More local work is on our recent projects page.

Gas across Chifley

  • Around Mawson Parade and Dr Walters Park: older cottages with original gas lines, and new homes with bigger demand.
  • Along Anzac Parade: units with cooktops on meter banks.
  • Near Chifley Public School: family homes, townhouses and duplexes.
  • The Little Bay side: newer homes with continuous flow and BBQ points.
  • The Matraville side: older streets with a mix of old and new gas set-ups.

Outdoor BBQ points

Many Chifley families cook outside, and a fixed natural gas point means no more swapping bottles. We run a gas line to the deck, alfresco area or outdoor kitchen, fit a bayonet or fixed connection, and test it. Natural gas BBQs need the right jets and regulator for natural gas; a BBQ set up for LPG can't simply be connected to natural gas without conversion by the maker or an authorised technician. If the BBQ point is a long way from the meter, we'll check the pipe size so the BBQ gets enough gas while other appliances are running.

Supply sizing in bigger homes

Every gas appliance has a rated gas use. Add them up, and you get the total load the meter and pipes need to carry when everything runs at once. In a large Chifley home with two continuous flow units, a five-burner cooktop, heating and a BBQ point, that total can be high. If the pipe is too small or too long for the load, pressure drops at the far appliances. The usual signs are hot water going cold when the cooktop is on, flames lifting or going out, or error codes on the hot water. We calculate the load and pipe sizes, and fix the supply so every appliance gets the gas it needs.

Cooktops and ovens

Swapping a gas cooktop is one of the most common gas jobs we do in Chifley. The new cooktop needs the right connection, a regulator if required, and enough clearance from range hoods and walls. We disconnect the old one, connect the new one with approved fittings, pressure test, and check each burner lights cleanly with a blue flame. If the cooktop is moving to a new spot in the kitchen, we extend the gas line to suit.

Heaters and bayonets

Gas bayonets let you plug in a portable gas heater where you need it. Older Chifley homes often have bayonets in old spots that no longer suit the furniture layout, or none in the rooms where they're wanted. We can add new bayonets, move existing ones, or cap off ones you no longer use. Gas heaters need good ventilation, and flued heaters must have their flues kept clear and in good condition.

Continuous flow hot water

Continuous flow gas hot water is common in newer Chifley homes and townhouses. When a unit fails, it usually shows an error code. Common causes include ignition faults, blocked air intakes, low gas pressure and failed sensors. We diagnose the fault and repair it, or replace the unit if it's old and parts are scarce. When replacing, we check the gas supply, the flue clearances from windows and doors, and the water pipe sizes. See hot water in Chifley.

Going electric?

Some Chifley households are switching to induction cooktops and heat pumps. When a gas appliance is removed, the gas point should be capped off properly and the system pressure tested. If every gas appliance is going, the gas can be disconnected at the meter by the network. We cap and test points, and give you the paperwork for the work done.

Buying or rebuilding in Chifley?

If you're buying an older Chifley home, a gas check is worth doing alongside the building inspection. We pressure test the system, check the appliances, and let you know about any old lines or points that need attention. If you're planning a knock-down rebuild, the old gas service needs disconnecting before demolition, and the new home's gas needs to be planned for all the appliances you want. Planning the gas load early avoids surprises later.

Gas lines under older floors

In Chifley's older cottages, gas lines often run under the timber floor from the meter to the kitchen, the hot water and any heater points. Over the decades, these lines get extended, rerouted and joined. Some joins were done well; others weren't. Old pipe can corrode where it touches damp soil or brickwork, and fittings can loosen as floors move. A pressure test tells us whether the whole system is sound. If it isn't, we track down the leak, usually with a detector along the line, and repair or replace the section. Where the old line is in poor condition, replacing the run from the meter is often the better long-term choice.

Gas hot water in older homes

Some older Chifley homes have a gas storage tank down the side of the house or in the laundry. When it fails, there's a choice: another storage tank, a continuous flow unit, or a switch to a heat pump. Continuous flow needs more gas than a storage tank at peak, so the meter, regulator and pipe usually need checking and often upgrading, as in the Maroubra job above. We'll explain the options, the work involved for each and the fixed price, so you can choose what suits your household.

Gas in knock-down rebuilds

Before an old Chifley home is demolished, the gas supply must be safely disconnected. When the new home is planned, it's worth thinking about every gas appliance you might want, now and later: hot water, cooktop, oven, heating, BBQ, and perhaps a pool heater. The total gas load sets the meter size and the pipe sizes. Planning it early means the right meter is ordered, pipes are sized properly and run before the slab and walls go in, and you don't end up with appliances that starve each other. We're happy to look at your plans and work through the gas layout with you.

Flue clearances

Gas hot water units and flued heaters release exhaust gases. The rules set minimum distances between flues and windows, doors, vents and boundaries, so exhaust can't come back inside. In Chifley's townhouses and duplexes, where homes are close together, these clearances often decide where a replacement unit can go. If the existing spot no longer meets the rules, we'll suggest a compliant location nearby. We check clearances on every hot water install and replacement.

Small jobs, done properly

Many gas jobs are small: swapping a cooktop, moving a bayonet, fixing a burner that won't light. They still need a licensed gasfitter, approved fittings, a pressure test and the right paperwork. We treat a small job with the same care as a big one. We also check the rest of the system while we're there, so you know your gas is safe.

Before you call

  1. Note the appliance brand and model.
  2. Note any error code on a continuous flow unit.
  3. Take photos of the meter, the appliance and where you'd like a new point.
  4. Tell us about access: under-floor space, stairs, gates and parking.
  5. List everything you'd like done, so we can plan the supply and bring the right fittings.

Looking after gas appliances

  • Have gas heaters serviced every two years, or as the maker recommends.
  • Keep the flue and air intake of hot water units clear.
  • Clean cooktop burners so flames stay blue.
  • Don't block wall vents in rooms with gas heaters.
  • Turn off gas at the appliance if it won't light, and call us.
  • Know how to turn off the gas at the meter.

Gas or induction?

If you're replacing a cooktop, you might be weighing up gas against induction. Gas gives instant, visible heat and works with any cookware. Induction is fast, easy to clean and doesn't burn gas indoors, but it needs suitable cookware and a dedicated electrical circuit from an electrician. Some households keep gas for the hot water and BBQ and go induction in the kitchen. Others keep gas throughout. There's no single right answer. If you choose induction, we can cap off the old gas point and test the system. If you stay with gas, we'll connect the new cooktop properly.

Gas heaters and ventilation

Unflued gas heaters release their combustion products into the room, so they need permanent ventilation and should be serviced regularly. Flued heaters send exhaust outside through a flue, which must be kept clear and in good condition. If a heater has soot marks, yellow flames, a strange smell or makes you feel unwell, turn it off and have it checked. In Chifley homes with young children, a regular heater service before winter is worth doing.

Why the regulator matters

A gas regulator keeps the pressure steady for your appliances. The meter regulator controls pressure for the whole home, and some appliances have their own. If a regulator is too small for the load or failing, appliances can underperform, flames can flicker, and continuous flow units can show error codes. Replacing an undersized meter regulator is often part of upgrading to continuous flow, as it was in the Maroubra job above.

Gas safety in shared buildings

In units and townhouse complexes, gas lines can run through common areas and past other homes. A leak on a shared line affects everyone, so it's important to report any smell straight away. If you smell gas in a stairwell or near a meter bank, let the owners corporation know and, if the smell is strong, call Jemena. For work inside your own home, call us and we'll make sure your side is safe.

Why Chifley homeowners call us

We're licensed plumbers and gasfitters (licence 398171C), a few minutes away in Matraville. We pressure test every job, lodge the paperwork the law requires, and explain what we've done in plain language. You'll get options and a fixed price before any work starts, and our workmanship carries a lifetime labour warranty. Whether it's a new cooktop, a BBQ point on the deck or a gas supply that can't keep up with a growing family, we'll get it right.

If you're planning gas work, send us photos of the meter and where you'd like the new point, and we'll tell you what's involved before we come out.

Gas words explained

  • Bayonet: a wall or floor fitting for plugging in a portable gas heater.
  • Regulator: controls the gas pressure to an appliance or the home.
  • Pressure test: a test that confirms the gas system has no leaks.
  • Certificate of compliance: the paperwork lodged after gas work in NSW.
  • Flue: carries exhaust gases from an appliance to outside.
  • Gas load: the total gas the appliances use when running at once.

What happens when you call

1

Tell us what's going on

Call or send a quick form. A photo of the problem helps us come prepared. No call-out fee.

2

Options and a fixed price first

We find the cause, explain your options and give you a fixed price for each before any work starts.

3

Fixed, tested and backed

We do the work, test it, clean up, and back our workmanship with a lifetime labour warranty.

Jobs we finished recently

Our van on a job in Little Bay
Our van on a job in Little Bay

See more recent projects

Why Chifley homeowners call us

  • Based in Matraville, a few minutes from Chifley
  • Rated 5.0 from 110 Google reviews
  • Free quotes, with options and a fixed price before any work starts
  • Lifetime labour warranty on our workmanship
  • Licensed plumbers, drainers and gasfitters (Lic. 398171C)

Gas fitting questions from Chifley homeowners

Do I need a licensed gasfitter to connect a cooktop?

Yes. In NSW, gas work must be done by a licensed gasfitter.

Why does my hot water go cold when the cooktop is on?

The gas supply is probably too small for both at once. We can resize it.

Can you run a gas point for my BBQ?

Yes, to a deck, alfresco area or outdoor kitchen.

Can I connect an LPG BBQ to natural gas?

Not without conversion by the maker or an authorised technician.

My continuous flow unit shows an error code. Can you fix it?

Yes. Note the code and brand when you call.

Can you move my gas bayonet?

Yes, or add new ones.

My cooktop flames are yellow. Is that a problem?

It can be. Turn it off and have it checked.

Can you cap off gas if I go electric?

Yes, with a pressure test and paperwork.

What's a certificate of compliance?

The paperwork lodged after gas work, as required in NSW.

Should I have gas checked before buying?

It's a sensible check, especially in older homes.

How long does a cooktop swap take?

Usually an hour or two.

What warranty do I get?

Our workmanship carries a lifetime labour warranty.

More plumbing in Chifley: our Chifley plumber page, hot water and blocked drains. Nearby: gas fitting in Little Bay, Malabar and Matraville. Guides: gas fitting, gas compliance certificates and gas point installation.

Call 0401 758 373Free quote