★★★★★ 5.0 from 100+ Google reviews · Your Sydney Plumber

Gas fitting in Randwick 2031

Our licensed gasfitters look after gas in Randwick homes: cooktop and oven connections, heater bayonets, gas storage and continuous flow hot water, old gas lines in terraces and Federation houses, gas leak checks and capping off old points. Every job is pressure tested and certified, and you get options and a fixed price before any work starts. Our workmanship carries a lifetime labour warranty.

Many Randwick homes have had gas for a very long time. Victorian terraces, Federation houses and interwar flats were connected decades ago, and their gas lines have been extended, patched and rerouted as stoves, heaters and hot water came and went. Old fireplaces were converted to gas heaters, and bayonets were added in the rooms people used most. Today that can mean undersized pipes, old points nobody uses, and joins that have never been tested. We come up from Matraville to make Randwick gas safe, tidy and right for the appliances you use now.

Gas work we do in Randwick

Cooktops and ovens

New cooktops and ovens connected, or old ones swapped, with approved fittings and a pressure test.

Heater bayonets

Bayonets added or moved, and old fireplace gas points checked or capped.

Gas hot water

Storage and continuous flow units connected or replaced, with the supply sized for them.

Old gas lines

Ageing lines under floors and in walls tested, repaired or replaced.

Leak checks

The whole system pressure tested to confirm it's sound.

Capping off

Old points capped and tested when appliances go electric.

Signs you need a gasfitter

  • A gas smell near an appliance, the meter or under the floor.
  • Yellow or orange flames on the cooktop instead of blue.
  • Soot around a heater or fireplace insert.
  • Hot water goes cold when the cooktop or heater is on.
  • A burner won't light or keeps going out.
  • An error code on a continuous flow unit.
  • Old gas points in rooms that no longer use them.
  • A higher gas bill with no change in use.

Why gas jobs come up in Randwick

Old lines in old houses

Randwick is one of Sydney's oldest suburbs. Gas lines in terraces and Federation houses were laid long ago and extended many times. Old steel pipe can corrode, and joins made decades ago may never have been tested to today's standards.

Converted fireplaces

Many older homes had their fireplaces converted to gas log fires or gas heaters at some point. The gas points and flues behind them need to be in good condition, and some are no longer used at all.

Undersized supply

Lines sized for a stove and a small heater often can't keep up with a modern cooktop, continuous flow hot water and a couple of heaters at once.

Flats and meter banks

Interwar flats often have a bank of gas meters, with lines running through common areas. Work on your own appliances is yours to arrange; shared lines are the owners corporation's.

Heritage streets

In heritage conservation areas, new meters, pipes and gas hot water units are best kept out of sight from the street.

Randwick homes and their gas

Home typeTypical gas set-upCommon jobs
Terraces and semisOlder lines under floors, converted fireplaces, cooktopLine testing, bayonets, capping old points
Federation housesLong runs to heaters and hot waterSupply upgrades, continuous flow, leak checks
Interwar flatsMeter banks, cooktopsCooktop swaps, capping off, leak checks
Newer homes and unitsContinuous flow, cooktopsError codes, flue clearances

How a gas job runs

  1. Talk it through: what you want connected, moved, fixed or capped.
  2. Check the supply: meter, regulator and pipe sizes.
  3. Give you options with a fixed price for each, before any work starts.
  4. Do the work with approved pipe and fittings.
  5. Pressure test the system to confirm there are no leaks.
  6. Commission the appliance and check the flame and operation.
  7. Lodge the certificate of compliance as required in NSW.

Repair, extend or new line?

SituationUsually best
Swapping a cooktop on an existing pointConnect the new cooktop and test
Old fireplace gas point no longer usedCap and test
Adding a heater bayonetExtend the line
Adding continuous flow to an older homeCheck the supply, likely upsize the line or regulator
Old line leaking under the floorRepair or replace the section
Going electricCap and test the old points

What affects the cost

  • The type of job: connection, new point, new line or repair.
  • The distance from the meter or existing line.
  • Access: under floors, through sandstone footings, in tight spaces.
  • Whether the supply needs upsizing.
  • The appliance and its connection requirements.

You get a fixed price for each option before any work starts.

Who's responsible?

  • You: gas pipes and appliances on your side of the meter.
  • Owners corporation: shared gas lines in a block of flats.
  • Your gas network: the meter and the supply up to it.

Safety checks you can do

  1. Know where your meter is and how to turn it off.
  2. Look at your cooktop flames: blue with a small steady tip.
  3. Check for soot around heaters and fireplace inserts.
  4. Keep vents and the area around the hot water unit clear.
  5. If a smell comes and goes, note when and where, and call us.

Signs it's urgent and when it can wait

  • Act straight away if the gas smell is strong: turn off at the meter, get out, call Jemena, then us.
  • Call soon if there's a faint smell, yellow flames, soot or no hot water.
  • Book a time if you're planning a new cooktop, heater point or hot water change.

A recent gas job nearby

Here's a recent gas hot water job nearby in Maroubra, where the gas supply had to be upgraded for the new unit.

Old gas tank replaced with continuous flow, Maroubra (nearby)

The problem: the gas storage tank down the side of a Maroubra home had stopped sending hot water to the taps.

What we did: we explained repair against replacement and the systems that would suit, and the owners chose a Rinnai continuous flow unit. We removed the old tank, mounted the new unit on the wall, upsized the copper pipework, and replaced the gas regulator at the meter so the new system gets enough gas.

The result: reliable hot water at every tap, on a gas supply sized for the new unit.

Old gas hot water tank before replacement near Randwick
The old tank, Maroubra
New continuous flow gas hot water unit near Randwick
The new continuous flow unit

“Great plumber, fixed my leaking taps quickly and at a great price!”

Tom (Google review)

More local work is on our recent projects page.

Gas across Randwick

  • Around the Junction: units and newer homes with continuous flow.
  • Near the hospital and university: flats on meter banks and shared houses.
  • Towards Centennial Park and the racecourse: Federation houses with long gas runs.
  • On the slopes towards Coogee and Clovelly: terraces and semis with older lines.
  • In the heritage conservation areas: homes where meters and units should stay out of sight.

Converted fireplaces and gas heaters

A gas log fire or gas heater in an old fireplace is a lovely feature of many Randwick homes. It needs a sound gas connection, a clear and intact flue or chimney, and regular servicing. If a fireplace heater has soot marks, yellow flames or a smell, turn it off and have it checked. If you no longer use it, have the gas point capped and tested. Old fireplace gas points that were disconnected decades ago and never capped properly are something we find surprisingly often.

Cooktops and ovens

Swapping a gas cooktop is one of the most common gas jobs we do. The new cooktop needs the right connection, a regulator if required, and enough clearance from range hoods and walls. We disconnect the old one, connect the new one with approved fittings, pressure test, and check each burner lights cleanly with a blue flame. In older kitchens, we check the line feeding the cooktop too.

Heaters and bayonets

Gas bayonets let you plug in a portable heater where you need it. Older homes often have bayonets in spots that no longer suit the layout. We can add, move or cap off bayonets. Gas heaters need good ventilation, and flued heaters must have their flues kept clear.

Continuous flow hot water

Continuous flow units free up space inside a terrace and never run out, but they need enough gas and a compliant flue position. When we install or replace one, we check the gas supply, the flue clearances from windows and doors, and whether the unit will be visible from a heritage street. See hot water in Randwick.

Gas lines under old floors

In Randwick's terraces and Federation houses, gas lines usually run under timber floors on sandstone footings, from the meter to the kitchen, heaters and hot water. Over a century, those lines have been extended, rerouted and joined by many hands. Old steel pipe can corrode where it touches damp soil or stone. A pressure test tells us whether the whole system is sound. If it isn't, we track down the leak and repair or replace the section. Where the old line is in poor condition, replacing the run from the meter is often the better long-term choice, and it gives you a supply sized for modern appliances.

Supply sizing

Every gas appliance has a rated gas use. Add them up and you get the total load the meter and pipes must carry when everything runs at once. Older Randwick homes often have pipes sized for a stove and one heater. Add a continuous flow unit, a bigger cooktop and a couple of heaters, and pressure drops at the far appliances. The signs are hot water going cold when the cooktop is on, flames lifting, or error codes. We calculate the load and fix the supply.

Why the regulator matters

A gas regulator keeps the pressure steady for your appliances. If it's too small or failing, appliances underperform, flames flicker and continuous flow units show error codes. Replacing an undersized meter regulator was part of the Maroubra job above.

Flue clearances

Gas hot water units and flued heaters release exhaust gases. The rules set minimum distances from windows, doors, vents and boundaries. On close-set Randwick streets and narrow terrace blocks, these clearances often decide where a unit can go. We check clearances on every install and suggest a compliant spot.

Gas or induction?

If you're replacing a cooktop, you might be weighing up gas against induction. Gas gives instant, visible heat. Induction is fast and easy to clean, but needs suitable cookware and a dedicated circuit from an electrician. If you choose induction, we can cap off the old gas point and test the system.

Gas heaters and ventilation

Unflued gas heaters need permanent ventilation and regular servicing. Flued heaters and fireplace inserts must have their flues kept clear and in good condition. If a heater has soot marks, yellow flames, a smell, or makes anyone feel unwell, turn it off and have it checked.

Before you call

  1. Note the appliance brand and model.
  2. Note any error code on a continuous flow unit.
  3. Take photos of the meter, the appliance and where you'd like a new point.
  4. Tell us about access: under-floor space, stairs and parking.
  5. List everything you'd like done, so we can plan the supply.

Looking after gas appliances

  • Have gas heaters and fireplace inserts serviced every two years, or as the maker recommends.
  • Keep the flue and air intake of hot water units clear.
  • Clean cooktop burners so flames stay blue.
  • Don't block wall vents in rooms with gas heaters.
  • Know how to turn off the gas at the meter.

Buying an older Randwick home?

If you're buying a terrace, Federation house or flat in Randwick, a gas check is worth doing alongside the building inspection. We pressure test the system, check the appliances and look for old points that were never capped. You'll know what needs attention before you settle.

Old heater points nobody uses

Many older homes have gas bayonets, old fireplace connections or capped-off pipes from long-gone stoves. An old point that's been painted over, knocked or left uncapped can become a weak spot. If you don't need it, have it capped off properly and tested. If you'd like to use it again, we'll check it's safe first.

Gas in flats

In Randwick's interwar walk-ups, gas often comes from a bank of meters near the front or the stairwell, with lines running up through the building. If you smell gas in a stairwell or near the meters, let the owners corporation know and, if the smell is strong, call Jemena. For work inside your own flat, such as a cooktop swap or capping an old point, call us and we'll make sure your side is safe.

Small jobs, done properly

Many gas jobs are small: swapping a cooktop, moving a bayonet, capping an old fireplace point or fixing a burner that won't light. They still need a licensed gasfitter, approved fittings, a pressure test and the right paperwork. We treat a small job with the same care as a big one.

Planning new gas work

If you're planning a new kitchen layout, an outdoor area or a hot water change, think about the gas early. The position of the cooktop, BBQ and hot water, and the total gas load, decide the pipe route and size. Planning it first means everything works properly together.

Why Randwick homeowners call us

We're licensed plumbers and gasfitters (licence 398171C), coming up from nearby Matraville. We know Randwick's older homes and their gas quirks, pressure test every job, lodge the paperwork the law requires, and explain what we've done in plain language. You'll get options and a fixed price before any work starts, and our workmanship carries a lifetime labour warranty.

Gas meters in heritage streets

In Randwick's heritage conservation areas, the look of the street matters. Gas meters, new pipe runs and wall-mounted hot water units are best placed where they can't be seen from the front. When we upgrade a supply or install a new appliance, we look for a route along a side or rear wall, or under the floor, that keeps the work out of sight. If the meter itself needs to move, that's arranged with the gas network, and we'll explain the process.

Outdoor BBQ points

A fixed natural gas point on the back deck or courtyard means no more swapping bottles. We run the line, fit a bayonet or fixed connection, and test it. Natural gas BBQs need the right jets and regulator for natural gas; an LPG BBQ can't simply be connected without conversion by the maker or an authorised technician. If the BBQ point is a long way from the meter, we check the pipe size so it gets enough gas while other appliances are running.

Gas safety in winter

Winter is when gas heaters and fireplace inserts work hardest, and when windows are closed. Before the cold months, have heaters serviced, check flues and chimneys are clear, and make sure vents aren't blocked. If anyone feels headachy, dizzy or unwell when a heater is on, turn it off, open windows and have it checked before using it again. Never use an outdoor BBQ or patio heater indoors.

Gas hot water in tight spaces

In a terrace, a gas storage tank in a narrow side passage can be hard to service and replace. Switching to a wall-mounted continuous flow unit can free up the passage, as long as the gas supply is big enough and the flue position meets the rules. We'll check both before recommending it.

Shared houses and gas

Many Randwick homes near the hospital and university are shared by several adults. That usually means more cooking, more hot water and more heaters running at once than the gas supply was designed for. If the hot water goes lukewarm at peak times or burners struggle when everyone is home, the supply may need upsizing. If you own a shared house, a gas safety check every couple of years, covering heaters, cooktops, flues and a pressure test, gives you and the people living there peace of mind. We can arrange a time that suits everyone and keep the work quick and tidy.

However old your gas system is, the goal is the same: appliances that work properly, pipes that are sound, and paperwork that shows the job was done right.

Gas words explained

  • Bayonet: a wall or floor fitting for plugging in a portable gas heater.
  • Regulator: controls the gas pressure to an appliance or the home.
  • Pressure test: a test that confirms the gas system has no leaks.
  • Certificate of compliance: the paperwork lodged after gas work in NSW.
  • Flue: carries exhaust gases from an appliance to outside.
  • Gas load: the total gas the appliances use when running at once.

What happens when you call

1

Tell us what's going on

Call or send a quick form. A photo of the problem helps us come prepared. No call-out fee.

2

Options and a fixed price first

We find the cause, explain your options and give you a fixed price for each before any work starts.

3

Fixed, tested and backed

We do the work, test it, clean up, and back our workmanship with a lifetime labour warranty.

Jobs we finished recently

Our van on a job in Little Bay
Our van on a job in Little Bay

See more recent projects

Why Randwick homeowners call us

  • Based in Matraville, a short drive up from Matraville
  • Rated 5.0 from 110 Google reviews
  • Free quotes, with options and a fixed price before any work starts
  • Lifetime labour warranty on our workmanship
  • Licensed plumbers, drainers and gasfitters (Lic. 398171C)

Gas fitting questions from Randwick homeowners

Do I need a licensed gasfitter to connect a cooktop?

Yes. In NSW, gas work must be done by a licensed gasfitter.

My old fireplace has a gas point. Is it safe?

It should be checked. If you don't use it, we can cap and test it.

Why does my hot water go cold when the cooktop is on?

The gas supply is probably too small for both at once. We can resize it.

Can you move my gas bayonet?

Yes, or add new ones.

Which gas meter is mine in our block?

Usually labelled by unit number. We can help identify it.

My continuous flow unit shows an error code. Can you fix it?

Yes. Note the code and brand when you call.

I'm in a heritage area. Can I still get continuous flow?

Usually, in a position that's out of sight from the street.

My cooktop flames are yellow. Is that a problem?

It can be. Turn it off and have it checked.

Can you cap off gas if I go electric?

Yes, with a pressure test and paperwork.

What's a certificate of compliance?

The paperwork lodged after gas work, as required in NSW.

Should I have my gas checked before buying?

It's a sensible check, especially in older homes.

What warranty do I get?

Our workmanship carries a lifetime labour warranty.

More plumbing in Randwick: our Randwick plumber page, hot water and blocked drains. Nearby: gas fitting in Matraville and Malabar. Guides: gas fitting, gas compliance certificates and gas point installation.

Call 0401 758 373Free quote