★★★★★ 5.0 from 100+ Google reviews · Your Sydney Plumber

Hot water repairs and replacement in Banksmeadow 2019

We repair and replace hot water for Banksmeadow factories, warehouses, workshops and offices, and for the homes near Botany: storage and continuous flow systems in staff amenities and showers, units under kitchenette sinks, wall-mounted boiling water units, and the thermostatic mixing valves that keep staff showers and basins at a safe temperature. We find the fault, tell you whether it's worth repairing, and give you options with a fixed price before any work starts. We offer same-day service.

Hot water on an industrial site isn't a luxury. Staff need to wash their hands, shower after a dirty shift and make a cup of tea at smoko, and some sites need hot water for cleaning and wash-down. When the system in the amenities block fails, the whole shift notices. Banksmeadow's factories and warehouses have everything from a small electric unit under a kitchenette sink to banks of storage heaters in a change room. We're based a few minutes away in Matraville and we look after hot water at factory complexes along Beauchamp Road.

Hot water we look after in Banksmeadow

Amenities and change rooms

Storage and continuous flow systems serving staff showers and basins, gas or electric.

Kitchenettes and lunchrooms

Small electric units under the sink and point-of-use heaters.

Boiling water units

Wall-mounted boiling and chilled water units above lunchroom sinks, repaired or replaced.

Thermostatic mixing valves

TMVs on staff showers and basins, tested, serviced and replaced.

Wash-down and cleaning

Hot water for cleaning areas, wash bays and equipment.

Homes near Botany

Gas, electric, continuous flow and heat pump systems in the homes and units on the Botany side.

Signs your hot water needs attention

  • No hot water in the amenities, or it runs cold halfway through the shift.
  • Water that's too hot or too cold at a staff shower or basin, which can mean a TMV is failing.
  • Rusty or discoloured hot water.
  • Water around the base of a storage heater, or dripping from the relief valve drain.
  • A boiling water unit that leaks, won't heat, or keeps tripping.
  • An error code on a continuous flow unit, or a pilot that keeps going out on a gas system.
  • Rumbling or banging from a storage heater as it heats.

Why hot water fails on Banksmeadow sites

Heavy use by a whole shift

A hot water system serving a change room may run flat out at the end of every shift. Storage systems sized for an office can't keep up with a dozen showers at once, and continuous flow units in a busy amenities block cycle many times a day. Systems that work hard wear faster, so elements, thermostats, valves and anodes need attention sooner than at home.

Sand, scale and sediment

Sediment settles at the bottom of storage heaters, and on older water services sand and scale come through the pipes too. Sediment insulates the element or burner from the water, so the system works harder and makes rumbling noises, and it can block valves and strainers on continuous flow units and boiling water units.

Salt air near the bay

Banksmeadow is on the shore of Botany Bay, and salty air is hard on anything metal outside: hot water units on external walls, gas fittings, valves and the cases of continuous flow heaters. Corroded relief valves, isolation valves and unions are common on outdoor systems here.

Old systems nobody owns

On a site that has changed tenants a few times, the hot water system in the amenities can be older than anyone working there, with no service history. It keeps going until one day it doesn't. A quick check of its age and condition lets you plan a replacement instead of losing hot water mid-week.

Banksmeadow sites and their hot water

Type of siteTypical hot waterCommon problems
Factory units in a complexSmall storage unit in each unit's amenities, kitchenette unitOld units with no service history, leaking relief valves
Warehouses with change roomsLarger storage or continuous flow, sometimes several unitsNot enough hot water at shift change, worn TMVs
WorkshopsStorage unit for basins and a shower, sometimes wash-downSediment, corroded valves, outdoor units affected by salt air
Offices and showroomsUnder-sink units, boiling water unitsLeaking boiling water units, failed elements
Homes near BotanyGas or electric storage, continuous flowAgeing tanks, corroded outdoor valves

How we repair or replace hot water

  1. Talk it through. Tell us what's happening and send a photo of the system's label if you can, so we know the brand, size and age.
  2. Find the fault. We test the element, thermostat, burner, valves and controls, and check the TMV if there is one.
  3. Repair or replace? If it's worth repairing, we'll tell you. If it's near the end of its life, we'll say so and explain why.
  4. Give you options with a fixed price for each: like-for-like, a larger unit, continuous flow or a heat pump, depending on your site.
  5. Do the work at a time that suits your site, with the water off for as short a time as possible.
  6. Test and commission the system, set the temperatures, and test any TMVs.

A recent job nearby

Here's a recent job at a factory complex on Beauchamp Road in Matraville, just up the road from Banksmeadow.

Leaking boiling water unit replaced in a factory kitchenette, Matraville (nearby)

The problem: in a factory unit on Beauchamp Road, Matraville, the wall-mounted Zip boiling water unit above the kitchenette sink had started leaking.

What we did: we isolated and drained the unit, took it off the wall and fitted a new 3-litre Zip unit in the same spot, then filled it, powered it up and checked it reached temperature.

The result: the staff had boiling water back for their breaks, and the old leaking unit was taken away.

More local work is on our recent projects page.

Quick fix or long-term fix?

ProblemQuick fixLong-term fix
Not enough hot water at shift changeCheck and adjust the thermostatUpsize the system, add a second unit or move to continuous flow
Storage heater leaking from the tankNone, a leaking tank can't be repairedReplace the system
Relief valve drippingReplace the valveFit a pressure limiting valve if mains pressure is high
Boiling water unit leakingRepair the valve or seal if possibleReplace the unit
Shower temperature wanderingService the TMVReplace an old TMV and set a yearly test

What affects the cost

  • The type and size of system you need.
  • Gas or electric, and whether the connection is already there.
  • Access: systems in ceiling spaces, plant rooms or tight cupboards.
  • TMVs, valves and pipework that need replacing at the same time.
  • Timing: working outside your business hours.

You get a fixed price for each option before any work starts.

Who's responsible?

  • The site owner or tenant: the hot water system and TMVs serving the building. Leases vary on who repairs and replaces them, so check yours.
  • Factory complexes: each unit's hot water usually belongs to that unit.
  • Gas supply: the network pipe and meter belong to the gas network; the pipes after the meter are yours.

Quick checks you can do

  1. Check the label on the system for its age, size and model.
  2. Make sure the power is on at the switchboard, or the pilot is lit on a gas system.
  3. Look for water around the base or a dripping relief valve drain.
  4. For continuous flow, note any error code on the controller.
  5. Check the boiling water unit's filter change date if it has one.

Signs it's urgent and when it can wait

  • Call straight away if a storage tank is leaking badly, there's a gas smell, or water near electrics.
  • Call soon if there's no hot water in the amenities, or a staff shower is running too hot.
  • Book a time if the system is old and you want to plan a replacement, or TMVs are due for their test.

Thermostatic mixing valves for staff

A thermostatic mixing valve blends hot and cold water so showers and basins deliver water at a safe, steady temperature. On a work site with staff showers, a TMV protects people from scalds if the hot water is set high to keep the system free of bacteria. Because it's a safety device, a TMV needs regular testing and servicing. We test the outlet temperature and the shut-off if the cold supply fails, service the valve, and replace it if it's worn. See TMV testing.

Boiling water units

Wall-mounted boiling and chilled water units are in most offices and lunchrooms. They work hard: on all day, filled and drained dozens of times. Filters need changing, valves and seals wear, and units eventually leak. We repair them where we can, change filters, and replace leaking or failed units with a new unit in the same spot, as we did at the Beauchamp Road complex.

Choosing a system for your site

OptionGood forThings to know
Electric storageSmall amenities, kitchenettes, sites without gasSimple and reliable; can run out at busy times if undersized
Gas storageAmenities with steady demandRecovers faster than electric; needs a gas supply and flue
Continuous flow gasChange rooms with peaks at shift changeDoesn't run out; needs the right gas supply size
Heat pumpSites wanting lower running costsWorks well in Sydney's climate; needs outdoor space and airflow
Under-sink unitsSingle basins or kitchenettes far from the main systemQuick hot water at the tap; small capacity

Hot water and legionella

Hot water stored at a low temperature can grow bacteria, including legionella. That's why storage systems are set to store water hot, and why a TMV is used to bring the temperature down at the outlet. If your system has been turned down to save energy or stop scalding, it's worth having the settings checked so you get safe storage and safe outlets.

Banksmeadow, area by area

  • Industrial estates off Botany Road: factory units with small storage systems in each unit's amenities.
  • Larger warehouses and logistics yards: change rooms with bigger systems and TMVs.
  • Near the port and the bay: outdoor systems and gas fittings exposed to salt air.
  • The Botany side: the small number of homes and units, with gas and electric storage systems.
  • Next door in Botany, Hillsdale and Matraville: we're in these streets and estates every week.

Planning a replacement

If your amenities system is ten years or older, rusting at the base, or running out sooner than it used to, plan its replacement before it fails. We'll look at what the site actually needs, which may be more or less than what's there now, and give you options with a fixed price for each. The work can be done early or on a weekend so staff don't go without.

Hot water words explained

  • Storage system: a tank that heats water and keeps it hot until it's used.
  • Continuous flow: heats water only as it's used, so it doesn't run out.
  • Heat pump: uses a fan and compressor to take heat from the air, using far less electricity.
  • TMV: thermostatic mixing valve, blends hot and cold to a safe temperature.
  • Relief valve: a safety valve that lets out water if temperature or pressure gets too high.
  • Anode: a metal rod in a storage tank that corrodes in place of the tank.

Homes in Banksmeadow

For the homes and units on the Botany side of Banksmeadow, we repair and replace gas, electric, continuous flow and heat pump systems, just as we do in Botany next door. Outdoor systems here are exposed to salt air from the bay, so we replace corroded valves and fittings at the same time as the system. See hot water in Botany.

Replacing a hot water system, step by step

  1. We confirm the size and type with you and order the new system.
  2. On the day, we isolate the water and power or gas and drain the old system.
  3. The old system is disconnected and removed, and we check the base, valves and pipes around it.
  4. The new system goes in with new valves, and a new TMV if one is needed.
  5. We fill it, purge the air, turn on the power or gas and check it heats.
  6. We set the temperatures, test the outlets and take the old system away.

A hot water care calendar

  • Every six months: ease the relief valve lever on storage systems, following the label.
  • Every year: test TMVs and have the system checked.
  • Every few years: check the anode on storage systems, and change boiling water unit filters as the maker suggests.
  • At ten years: start planning a replacement for storage systems.

Sizing hot water for a change room

The question isn't how many people work on the site, it's how many shower at the same time. A crew of ten finishing together and all showering within twenty minutes needs far more hot water in that window than an office of forty washing their hands through the day. When we size a system for a change room, we ask how many showers there are, how long a typical shower runs, how many people use them at shift change and whether there are other draws at the same time, like a wash-down hose or a lunchroom sink. Then we size the storage, the recovery rate or the continuous flow unit to match the peak, not the average.

If your current system keeps running out, it may simply be too small for how the site is used now. Sites change: a unit that was once a quiet storage warehouse may now have a busy workshop crew. A system that suited the old tenant can be wrong for the new one.

Hot water in a leased factory unit

When you lease a factory unit, the hot water system in its amenities is usually part of the building, and the lease decides who looks after it. Some leases make the tenant responsible for repairs and the owner for replacement; others put it all on one side. When we attend, we'll tell you clearly what failed, whether it's a repair or a replacement, and give you a short written note with photos. That makes it easy to pass on to the owner, or to claim back if the lease says the owner pays.

Outdoor systems and the bay air

Many factory units have their hot water system on an outside wall, beside the amenities or near the roller door. On a site this close to Botany Bay, that system lives in salty air. Its case, the gas regulator, the relief valve, the isolation valves and the unions on the pipes all corrode faster than they would inland. When we replace or repair an outdoor system here, we check every fitting around it, replace anything that's corroding, and use fittings that stand up better to the conditions, so the new system isn't let down by the old valves next to it.

When hot water is part of your process

Some sites use hot water for more than washing hands: cleaning down equipment, filling tubs or tanks, or washing parts. If hot water is part of how your business works, a breakdown stops more than the lunchroom. We'll look at how much you use, how quickly you need it and how hot it needs to be, and suggest a system that suits. In some cases a dedicated unit for the process, separate from the amenities, is the more reliable option.

What to tell us when you call

  • Where the system is: amenities, change room, kitchenette, outside wall or plant room.
  • What's on the label: brand, model, size and, if it's shown, the manufacture date.
  • Whether it's gas or electric, and whether anything else on site has lost power or gas.
  • What's happening: no hot water, not enough, too hot, leaking, an error code or a noise.
  • When the site is open, and whether a quiet time is better for the work.

With that information we can often bring the right parts on the first visit, which saves a second trip and gets hot water back sooner. A photo of the system and the label sent by text or email helps more than anything.

Keeping water hot and safe

There's a balance on every site between storing water hot enough to stop bacteria and delivering it cool enough not to scald. The answer is a system set to store water at the right temperature, with TMVs or tempering valves bringing it down at the outlets people use. If someone has turned the system down because a shower was too hot, the real fix is at the outlet, not the heater.

What happens when you call

1

Tell us what's going on

Call or send a quick form. A photo of the problem helps us come prepared. No call-out fee.

2

Options and a fixed price first

We find the cause, explain your options and give you a fixed price for each before any work starts.

3

Fixed, tested and backed

We do the work, test it, clean up, and back our workmanship with a lifetime labour warranty.

Jobs we finished recently

Old hot water system in Maroubra
Old hot water system in Maroubra
New hot water system in Maroubra
New hot water system in Maroubra

See more recent projects

Why Banksmeadow businesses and homeowners call us

  • Based in Matraville, a few minutes from Banksmeadow
  • Weekend and early starts when that keeps your site running
  • Rated 5.0 from 110 Google reviews
  • Options and a fixed price before any work starts
  • Lifetime labour warranty on our workmanship
  • Licensed plumbers, drainers and gasfitters (Lic. 398171C), with accredited backflow testers on the team

Hot water questions from Banksmeadow businesses and homeowners

Do you look after hot water in factories and warehouses?

Yes. We repair and replace hot water systems in staff amenities, change rooms and kitchenettes at factories, warehouses, workshops and offices in Banksmeadow and nearby.

Can you come today?

We offer same-day service. Tell us if the whole site has no hot water when you call.

Our change room runs out of hot water at shift change. What can we do?

The system may be too small for the demand. Options include a larger storage system, a second unit or continuous flow. We'll look at your use and give you prices.

Do you repair boiling water units?

Yes. We repair, service and replace wall-mounted boiling and chilled water units in lunchrooms and kitchenettes.

Do staff showers need a TMV?

A TMV keeps showers and basins at a safe temperature. Many workplaces have them, and they need regular testing. We test, service and replace them.

Can you replace our system without shutting the site down?

Yes. We plan the work for a quiet time and keep the water off for as short a time as possible.

Is it worth repairing an old storage system?

If the tank itself is leaking, no. If it's a valve, element or thermostat on a system that isn't too old, often yes. We'll tell you which.

Do you install heat pumps?

Yes, for homes and for sites with suitable outdoor space.

Who pays for hot water repairs in a leased unit?

It depends on your lease. We'll give you a clear note of the fault and the fix to pass on if needed.

Do you work on gas hot water?

Yes. We're licensed gasfitters, and we test and lodge the paperwork for gas work.

Do you still look after homes in Banksmeadow?

Yes. We look after hot water for the homes and units on the Botany side of Banksmeadow too.

Do you give a fixed price?

Yes, for each option, before any work starts.

More plumbing in Banksmeadow: our Banksmeadow plumber page, gas fitting, backflow testing and taps and toilets. Nearby: hot water in Botany and Hillsdale. Guides: hot water guide, TMV testing and dripping relief valves.

Call 0401 758 373Free quote