★★★★★ 5.0 from 100+ Google reviews · Your Sydney Plumber

Gas fitting in Banksmeadow 2019

We're licensed gasfitters for Banksmeadow factories, warehouses, workshops and offices, and for the homes near Botany: gas hot water for amenities and change rooms, cooktops in staff kitchens, gas heaters, new gas points, leak testing and repairs, corroded regulators and fittings, and the compliance paperwork that goes with them. If you smell gas, turn it off at the meter, leave the area and call Jemena on 131 909, then call us. We give you a fixed price before any work starts.

Gas on a work site is usually doing ordinary jobs, heating water for showers at the end of a shift, running a cooktop in the lunchroom or warming an office, but it needs to be done right. Banksmeadow sits on the shore of Botany Bay, where salt air corrodes regulators, meters and outdoor pipework, and older industrial buildings can have gas lines that have been extended and altered by several tenants over the years. We're licensed gasfitters based a few minutes away in Matraville.

Gas work we do in Banksmeadow

Gas hot water

Storage and continuous flow gas systems for amenities, change rooms and homes, repaired and replaced.

Staff kitchen cooktops

Gas cooktops in lunchrooms and kitchenettes, installed, replaced and tested.

Gas leaks

Leaks found by pressure testing and repaired, with the system tested before it goes back into use.

Regulators and fittings

Corroded regulators, unions and fittings near the meter and on outdoor pipework replaced.

New gas points

New points for heaters, cooktops, barbecues and hot water, sized for the load.

Compliance paperwork

A certificate of compliance for gas work, as the law requires.

Signs your gas needs attention

  • A smell of gas near an appliance, the meter or outdoor pipework.
  • Yellow or orange flames instead of blue on a cooktop or heater.
  • Soot or black marks around an appliance or flue.
  • A pilot light that keeps going out.
  • Hot water that runs cold when several outlets are used, which can mean the gas supply is too small.
  • Rust and green crust on the regulator, meter fittings or outdoor pipes.
  • A hissing sound near gas pipework.

If you smell gas

  1. Turn off the gas at the meter if it's safe to do so.
  2. Don't use switches, phones or anything that could spark near the smell.
  3. Open doors and windows.
  4. Get everyone out of the area.
  5. Call Jemena's faults line on 131 909.
  6. Then call us to find and fix the leak.

Why gas fittings fail in Banksmeadow

Salt air

Gas meters, regulators and outdoor pipework near Botany Bay sit in salty air all year. Brass and steel fittings corrode, regulator vents block and unions start to weep. A corroded regulator can also stop delivering the right pressure, so appliances run poorly.

Buildings altered over the years

Older factory and office buildings have often been fitted out by several tenants. Gas lines get extended, capped, rerouted and left behind. Old capped lines, undersized extensions and appliances added to a line that was never sized for them are common.

Heavy use

Gas hot water in a change room runs hard at every shift change. Burners, thermocouples, ignition systems and fans wear faster than on a home system.

Knocks and vibration

Gas pipes along walls and near loading areas get knocked, and vibration from machinery and trucks loosens fittings over time.

Banksmeadow sites and their gas

Type of siteTypical gas useCommon problems
Factory unitsGas hot water for amenities, sometimes a cooktopCorroded outdoor fittings, old hot water units
Warehouses with change roomsLarger gas hot water or continuous flowUndersized supply for the hot water, worn components
Offices and showroomsHeaters, kitchen cooktopsOld heaters, yellow flames, poor ventilation
WorkshopsHot water, heatersKnocked pipework, old capped lines
Homes near BotanyHot water, cooktops, heatersCorroded meters and regulators, old heaters

How we do gas work

  1. Talk it through and find out which appliances and what's happening.
  2. Check and test: we pressure test the line, check the regulator and look at every appliance on it.
  3. Find the fault: a leak, a failed regulator, a worn appliance part or an undersized supply.
  4. Give you options with a fixed price for each.
  5. Do the work at a time that suits your site.
  6. Test, commission and certify: the system is tested, appliances are lit and checked, and we provide the compliance certificate.

Recent gas jobs nearby

Here are two recent gas jobs close to Banksmeadow.

Old gas storage tank replaced with continuous flow, Maroubra (nearby)

The problem: an old gas storage tank beside a Maroubra home had stopped delivering hot water.

What we did: we explained repairing against replacing and the systems that would suit, and the owners chose a Rinnai continuous flow unit. We removed the tank, mounted the new unit on the wall, upsized the copper pipework and replaced the gas regulator at the meter so the new unit gets enough gas.

The result: reliable hot water throughout the house, on a properly sized gas supply.

Old gas hot water tank before replacement, near Banksmeadow
The old tank, Maroubra
New continuous flow gas unit installed, near Banksmeadow
The new continuous flow unit

Gas cooktop installed, Matraville (nearby)

The problem: a Matraville owner had bought a new gas cooktop and needed it fitted in place of the old one.

What we did: we disconnected and removed the old cooktop, cut back sections of tile and the benchtop to suit the new one, and fitted a new cement fibre base so it had a solid surface. A new gas flexible hose was connected to the cooktop's regulator, the cooktop was set in place and levelled, and the gas line was purged.

The result: every burner was tested and lit properly, and the new cooktop sits solid and level.

More local work is on our recent projects page.

Quick fix or long-term fix?

ProblemQuick fixLong-term fix
Gas leak at a fittingRemake or replace the fittingReplace corroded pipework near the meter
Corroded regulatorReplace itProtect outdoor fittings from the weather
Hot water runs cold at peak timesService the unitUpsize the gas supply or the unit
Yellow flamesClean and adjustService or replace the appliance
Old capped linesCheck they're sealedRemove redundant pipework

What affects the cost

  • The type of work: a repair, a new point or a replacement appliance.
  • The length and size of any new pipework.
  • Access: pipes in ceilings, walls or under slabs.
  • Testing and certification, included with the work.
  • Timing: outside your business hours.

You get a fixed price for each option before any work starts.

Who's responsible?

  • The site owner or tenant: gas pipes and appliances after the meter. Check your lease.
  • Jemena: the gas network, the main in the street, and faults on their side. Call 131 909 for a gas leak.
  • Your gas retailer: billing and supply.

Quick checks you can do

  1. Know where your gas meter is and how to turn it off.
  2. Look at flames on cooktops and heaters: they should be blue.
  3. Check around the meter and regulator for corrosion.
  4. Make sure flues and vents aren't blocked.
  5. Keep the area around gas appliances clear of stock and rubbish.

Signs it's urgent and when it can wait

  • Call Jemena straight away if you smell gas strongly, then call us.
  • Call soon if a pilot keeps going out, flames are yellow, or there's soot.
  • Book a time if you want a new gas point, a replacement appliance, or a check of old pipework.

Gas hot water for change rooms

Gas is a good fit for change rooms because it heats water quickly and continuous flow units don't run out. But a continuous flow unit needs a gas supply big enough to run it at full output. If staff find the water goes cold when several showers run, the gas pipe, the regulator or the meter may be too small. We check the supply and, where needed, upsize the pipework or regulator, as we did when replacing an old tank with a continuous flow unit in Maroubra. See hot water in Banksmeadow.

Compliance certificates

Gas work in NSW must be done by a licensed gasfitter, tested, and covered by a certificate of compliance. We provide it with every job that needs one, so you have it for the site owner, your insurer or the next tenant. See gas compliance certificates.

Banksmeadow, area by area

  • Industrial estates off Botany Road: factory units with gas hot water and outdoor meters.
  • Warehouses and logistics yards: change rooms with larger gas hot water systems.
  • Near the port and the bay: outdoor gas fittings in salty air.
  • The Botany side: homes and units with gas hot water, cooktops and heaters.
  • Next door in Botany, Hillsdale and Matraville: we do gas work here every week.

Gas words explained

  • Regulator: reduces gas pressure from the network to what appliances need.
  • Pressure test: testing a gas line to make sure it doesn't leak.
  • Purging: clearing air from a gas line before an appliance is lit.
  • Flue: the pipe that carries combustion gases away from an appliance.
  • Compliance certificate: the document confirming gas work meets the rules.
  • Jemena: the gas network operator in this area.

Homes in Banksmeadow

For the homes and units on the Botany side of Banksmeadow, we install and service gas hot water, cooktops and heaters, and replace corroded meters, regulators and fittings, just as we do in Botany. See gas fitting in Botany.

Testing a gas line for leaks, step by step

  1. We turn off every appliance on the line and the gas at the meter.
  2. A pressure gauge is connected to a test point on the pipework.
  3. The line is brought up to test pressure and the gauge is watched for a set time. If the pressure drops, there's a leak.
  4. We find the leak by checking each joint, fitting and appliance connection with leak detection fluid or an electronic detector.
  5. The leaking fitting is remade or replaced, and the line is tested again until it holds.
  6. Each appliance is purged, relit and checked for a clean, blue flame and correct operation.

If the leak is somewhere we can't see, such as a pipe in a wall or under a slab, we isolate sections of the line one at a time to narrow it down.

Gas meters and regulators near the bay

The gas meter and regulator on a Banksmeadow site are usually outside, on a wall near the street or in a meter box. In salty air off Botany Bay, they corrode faster than they would inland. The regulator's vent can block with corrosion or insects, the unions on either side start to weep, and the steel pipe coming out of the ground rusts. A corroded regulator may stop delivering the right pressure, so hot water units and cooktops run poorly or shut down. We replace corroded fittings and regulators on the customer side of the meter, and if the meter itself is the problem, we'll tell you so you can contact Jemena.

Gas heating in offices and showrooms

Some offices and showrooms are warmed by gas space heaters, either flued wall heaters or portable heaters on a bayonet point. Heaters that haven't been serviced for years can burn poorly, produce carbon monoxide and leave soot on walls. We service gas heaters, check flues and ventilation, and replace heaters that are past repair. If a heater has yellow flames, soot marks or a smell, stop using it until it's been checked.

Moving or adding to gas pipework

When a site is fitted out for a new tenant, gas pipework often needs to move: a new cooktop in a lunchroom, a hot water unit relocated to make room for racking, or a heater point removed. We size new pipework for the appliances it will serve, test the whole line after any change, and provide the compliance certificate. Old capped lines that are no longer needed are checked and removed, so nobody mistakes them for live gas later.

A third gas job: moving a gas meter

Gas and water meters moved, Matraville (nearby)

The problem: a Matraville owner wanted both the water meter and the gas meter moved further into the property, closer to the front of the house.

What we did: for the gas meter, we exposed the high-pressure nylon supply pipe in the front yard and squeezed it off with a special tool so the meter could be moved safely. For the water meter, we froze the incoming pipe so the meter could be moved without turning off the street main, then ran new copper pipe in a trench to the new meter position and connected it back into the house pipework.

The result: both meters sit about 1.5 metres further into the property, connected and tested.

Sizing a gas supply

Every gas appliance has a rated input, and the gas pipe, the regulator and the meter all have to be big enough to deliver the total when everything runs at once. A site that started with one small storage hot water unit and has since added a continuous flow unit, a cooktop and a heater may now be asking more of its gas supply than it can deliver. The signs are hot water that goes cold when the cooktop is on, burners that flicker or a unit that shows a gas supply error. We work out the total load, check the pipe sizes and lengths, and upsize what's needed.

Ventilation and flues

Gas appliances need air to burn and a way to get rid of the combustion gases. A hot water unit in a small cupboard, a heater with a blocked flue, or an appliance boxed in by racking or stock can run short of air and produce carbon monoxide. When we service or install an appliance, we check the ventilation and the flue, and if an appliance has been boxed in since it was installed, we'll tell you what needs to change.

Gas safety for staff

  • Show staff where the gas meter is and how to turn it off.
  • Put a sign near the meter with Jemena's faults number, 131 909.
  • Keep stock, pallets and rubbish clear of gas appliances and meters.
  • Report any gas smell, yellow flames or soot straight away.
  • Have gas appliances serviced as the maker recommends.

What to tell us when you call

  • Which appliances are affected and what's happening.
  • Where the gas meter is.
  • Whether you've smelled gas, and whether Jemena has been called.
  • Whether anything has changed recently, such as a new appliance or fit-out.
  • When the gas could be turned off for testing or repairs.

Replacing gas hot water in a factory unit

Many small factory units have a gas storage hot water unit on an outside wall, serving the amenities basin, a shower and the kitchenette. After ten years or more in salty bay air, the tank may be rusting at the base, the burner may be struggling, and the valves around it may be corroded. When it's time to replace it, we'll go through the options: like-for-like gas storage, continuous flow, or a move to electric or a heat pump if that suits the unit better. Whichever you choose, we replace the corroded valves and fittings around it and test the gas line before the new unit is lit.

Barbecues and outdoor gas points

Some sites have an outdoor area for staff with a gas barbecue on a bottle or a fixed gas point. A fixed point needs to be installed and tested by a licensed gasfitter, with the right fitting and isolation valve, and positioned well away from doors, vents and anything that could catch. We install outdoor gas points for homes and businesses and check existing ones for corrosion and leaks.

Before a new tenant moves in

When a factory unit or office changes hands, it's a good time to check the gas: a pressure test of the line, a look at the regulator and fittings, a service of the hot water unit and any heaters, and removal of any old capped lines left by the last tenant. It means the new tenant starts with a gas system that's safe and documented.

Why a licensed gasfitter matters

In NSW, gas work must be done by a licensed gasfitter, tested and certified. Work done without a licence can void insurance, fail an inspection and, worst of all, leave a leak or a poorly burning appliance that nobody knows about. Our gasfitters hold the licences for the work they do, test every job before the gas goes back into use, and give you the paperwork. If you're not sure who did the gas work on your site, we can check it for you.

What happens when you call

1

Tell us what's going on

Call or send a quick form. A photo of the problem helps us come prepared. No call-out fee.

2

Options and a fixed price first

We find the cause, explain your options and give you a fixed price for each before any work starts.

3

Fixed, tested and backed

We do the work, test it, clean up, and back our workmanship with a lifetime labour warranty.

Jobs we finished recently

Our van on a job in Little Bay
Our van on a job in Little Bay

See more recent projects

Why Banksmeadow businesses and homeowners call us

  • Based in Matraville, a few minutes from Banksmeadow
  • Weekend and early starts when that keeps your site running
  • Rated 5.0 from 110 Google reviews
  • Options and a fixed price before any work starts
  • Lifetime labour warranty on our workmanship
  • Licensed plumbers, drainers and gasfitters (Lic. 398171C), with accredited backflow testers on the team

Gas fitting questions from Banksmeadow businesses and homeowners

Do you do gas work in factories and warehouses?

Yes. We do gas hot water, cooktops, heaters, new gas points and leak repairs for factories, warehouses, workshops and offices in Banksmeadow and nearby.

What should we do if we smell gas?

Turn off the gas at the meter if it's safe, get people out, call Jemena on 131 909, then call us.

Can you find a gas leak?

Yes. We pressure test the line and find the leak, then repair and retest it.

Our change room hot water runs cold. Is it the gas?

It can be. A gas supply that's too small for a continuous flow unit is a common cause. We'll check it.

Do you provide a compliance certificate?

Yes, for all gas work that needs one.

Can you install a cooktop in our staff kitchen?

Yes, including a new gas point if one isn't there.

Our regulator is rusty. Should it be replaced?

If it's corroded, yes. A failing regulator can affect how every appliance runs.

Can you remove old gas pipes left by a previous tenant?

Yes. We check old capped lines and remove pipework that's no longer needed.

Can you work outside our business hours?

Yes. If the gas has to go off, we can do the work early or on a weekend.

Can you come today?

We offer same-day service for gas repairs. For a gas leak, call Jemena first.

Do you still look after homes in Banksmeadow?

Yes. We do gas work for the homes and units on the Botany side of Banksmeadow too.

Do you give a fixed price?

Yes, before any work starts.

More plumbing in Banksmeadow: our Banksmeadow plumber page, hot water, leak detection and backflow testing. Nearby: gas fitting in Botany and Hillsdale. Guides: gas fitting, gas compliance certificates and gas cooktop installation.

Call 0401 758 373Free quote