Leak detection in Pagewood 2035
A leak you can see is easy. The ones that cost Pagewood homeowners money are the ones you can't: water running into the sandy ground under the front lawn, a pipe weeping under a slab, a shower leaking into the wall cavity. Often the only clue is a water bill that's higher than it should be, or a meter that keeps ticking over when everything is off. We're based in Matraville, a few minutes away, and finding these leaks without pulling the house apart is a big part of what we do.
Signs you have a hidden leak
- A higher water bill with no change in how many people live there or how you use water.
- The meter moving when every tap and appliance is off.
- The sound of running water in a wall or under the floor when nothing is on.
- A warm patch on a tiled floor, which can mean a hot water pipe leaking underneath.
- Damp, bubbling paint or mould low on a wall, often beside a shower, bath or kitchen.
- Loose or drummy tiles around a shower or on a bathroom floor.
- A patch of lawn that stays green in dry weather, or a path that's always damp.
- Low pressure at every tap, which can point to a leak in the water service.
Before you call, try the simple meter test in our Pagewood water meter leak test guide. If the numbers move with everything off, there's a leak somewhere.
Where leaks hide in Pagewood homes
Under the front lawn, in sandy ground
Pagewood sits on sandy ground, and that changes how leaks behave. In clay, a leaking water service makes a wet patch or a puddle. In sand, the water just drains away, sometimes for months, without any sign on the surface. The pipe between the meter near the front fence and the house is one of the most common places we find a leak in Pagewood that nobody knew was there.
Under timber floors in older homes
The bungalows from the Monash Gardens estate in the north of the suburb and many of the post-war homes further south have timber floors over a crawl space. Water pipes run underneath, often old copper or galvanised steel. A pinhole or a failed joint drips onto the sand under the house and soaks away. The clues are a musty smell, damp under the floor and a meter that won't stop moving.
Under concrete slabs
Newer homes, rebuilds and townhouses near Wentworth Avenue are mostly on slabs, with pipes running through or under the concrete. A slab leak on the hot side often shows as a warm spot on the floor. On the cold side it can be completely silent. Finding these without breaking up the whole floor is about testing each section in turn.
Inside walls and showers
Showers are the classic hidden leak. Water gets behind the tiles through cracked grout or a failed seal around the tap or the waste, or the pipe connection to the shower mixer leaks inside the wall. The damage shows up later, on the other side of the wall or in the floor next to it.
Toilets, hot water and irrigation
Some of the biggest leaks aren't in the pipes at all. A toilet cistern that leaks into the bowl can waste a lot of water silently. A hot water relief valve that runs constantly sends water straight to the drain. A garden irrigation system with a broken dripper or a stuck valve can run for hours a day. We always check these first, because they're quick to rule in or out.
Pagewood homes and the leaks we find
| Home type | Most common leak | How we usually find it |
|---|---|---|
| 1920s bungalows (Monash Gardens estate) | Old copper or galvanised under timber floors | Isolate the house from the service, then inspect and test under the floor |
| Post-war brick homes off Page Street | Water service in the front yard, shower leaks | Meter tests with sections isolated, then the shower checked |
| Rebuilt and extended homes | Joints where new pipe meets old | Test old and new sections separately |
| Townhouses near Wentworth Avenue | Pipes in slabs and walls, shower waterproofing | Section testing, thermal checks, inspection of the shower |
| Homes with gardens near Bonnie Doon | Irrigation and garden taps | Shut off irrigation and outdoor lines and read the meter |
How we find a leak
- Confirm it. We read the meter with everything off to confirm water is escaping, and get a sense of how much.
- Rule out the easy ones. Toilets, the hot water relief valve, irrigation, pool top-ups and garden taps.
- Split the system. We isolate the water service from the house, then sections inside the house, reading the meter each time. This tells us which part of the plumbing the water is going from.
- Pinpoint it. Depending on where it is, that means listening along the pipe, thermal imaging for hot water leaks, moisture readings in walls and floors, or a look under the house.
- Show you and give options. We explain where the leak is and give you a fixed price for each way to fix it: repair the section, replace the run, or reroute the pipe.
- Fix and retest. After the repair we read the meter again with everything off to make sure the leak is gone and there isn't a second one.
Water service leaks
Leaks in the pipe from the meter to the house found and repaired, including in sandy front yards.
Under-floor leaks
Leaks under timber floors traced and fixed from the crawl space.
Slab leaks
Leaks in or under concrete narrowed down by section testing so only a small area is opened.
Shower and wall leaks
Leaks behind tiles and inside walls found, with the pipe or seal repaired.
Toilet and tap leaks
Silent cistern leaks and dripping taps found and fixed.
Hot water leaks
Relief valves, tank leaks and hot pipe leaks diagnosed and repaired.
Repair the leak or replace the pipe?
| What we find | Repair the spot | Replace or reroute |
|---|---|---|
| One failed joint on sound copper | Yes | Not needed |
| Old galvanised pipe leaking in several places | A short-term fix | Replace the galvanised section |
| Water service leaking in sandy ground | If the rest of the pipe is sound | A new service if it's old or has leaked before |
| Hot water pipe leaking in a slab | Sometimes, if it can be reached | Often a reroute through the wall or ceiling |
| Shower mixer connection leaking in the wall | Repair the connection | A new mixer if it's old |
| Shower leaking through the grout or seals | Reseal if it's caught early | Waterproofing work if water has got under the tiles |
What affects the cost
- How long it takes to pinpoint: a toilet leak is found in minutes; a slab leak takes more testing.
- Where it is: an accessible subfloor is quicker than a slab or a tiled wall.
- The repair: fixing a joint, replacing a section, or rerouting a pipe.
- Pipe condition: old galvanised or tired copper may need more replaced.
- Making good: lawn, paving, tiles or plaster after the repair.
You get a fixed price for each option before any repair starts.
Who's responsible for the leak?
- Sydney Water: the water main in the street and the meter. A leak at the meter or on the street side is theirs.
- You (the homeowner): every pipe on the house side of the meter, including the water service under the front yard.
- Townhouses and units: pipes inside your own home are usually yours. Shared pipes and common areas are usually the owners' together. A leak coming from the unit above is usually that owner's to fix.
Quick checks before you call
- Turn off every tap and water-using appliance, note the meter reading, wait an hour without using water, then read it again.
- Check each toilet: lay a strip of dry toilet paper across the back of the bowl under the rim. If it gets wet before the next flush, the cistern is leaking.
- Look at the relief valve drain on the hot water system. A steady stream or a pipe that's always wet needs checking.
- Turn off the irrigation system and any pool top-up and see if the meter stops.
- Feel tiled floors in bare feet for warm spots, and look low on walls near showers for damp or bubbling paint.
Signs it's urgent and when it can wait
- Call straight away if water is coming through a ceiling, running near electrics, or the meter is spinning fast.
- Call soon if the meter moves with everything off, a floor is warm, or there's new damp on a wall.
- Book a time if your bill is a bit higher than usual and you'd like it checked.
A recent leak job nearby
Here's a recent leak repair nearby in Chifley, a few minutes south of Pagewood.
Hidden toilet leak traced and repaired, Chifley (nearby)
The problem: water was escaping at the back of a toilet in a Chifley home, and the owners couldn't see where it was coming from.
What we did: we traced where the water was getting out at the back of the toilet and repaired it at the source rather than just drying it up.
The result: the floor stays dry and the toilet works without leaking.


More local work is on our recent projects page.
“I called [the team at] Scalici Plumbing Group to clear my blocked drain and fix my leaking toilet in Maroubra. Great company to deal with, highly recommended.”
Chris L., Maroubra (Google review)
Leaks across Pagewood, area by area
- The northern end near Astrolabe Park and Daceyville: the oldest homes, with copper and galvanised pipe under timber floors.
- Around Page Street and the school: post-war brick homes where the water service across the front yard is now decades old.
- The Dudley Street end: older cottages and rebuilds side by side, with leaks at the joins between old and new pipe.
- Near Bonnie Doon Golf Club: bigger gardens, where irrigation and garden taps are often the culprit.
- Towards Wentworth Avenue and Eastgardens: townhouses and apartments on slabs, with pipes in concrete and walls.
Leaks from the unit or townhouse next door
In the newer townhouses and apartments in Pagewood, a stain on your ceiling or a damp wall isn't always your plumbing. Water from a shower, bath or dishwasher next door or upstairs can travel a long way through walls and floors before it shows. We find where it's coming from first, so the right owner fixes it. If it's from another home, we'll give you a short written report with photos that you can pass to them or the owners corporation.
Leaks and the water bill
Water that leaks on your side of the meter goes through the meter, so you pay for it, and on most bills you pay sewer usage on it too. A small leak running all day adds up over a billing period. Keep our invoice, which describes the leak and the repair, with your water account papers. Then read the meter again a week or two later to make sure it's behaving.
Before a new bathroom or kitchen goes in
If a new bathroom or kitchen is about to go into in an older Pagewood home, it's the best time to deal with old pipe. With the walls and floor open, replacing old galvanised or tired copper costs far less than finding and fixing a leak in it after the new tiles are down. We can test the existing pipe before work starts and tell you what's worth replacing while it's exposed.
Common leak causes we see
- Old galvanised steel rusting from the inside until it pinholes.
- Copper rubbing against a brick pier, a bearer or a concrete edge until it wears through.
- Joints where old and new pipe were joined, especially copper to galvanised.
- High water pressure straining every fitting. A pressure limiting valve helps.
- Tree roots pushing on the water service under the front yard.
- Shower seals and grout that have cracked with age.
- Braided hoses under sinks and toilets that have perished. See flexi hose replacement.
Leak words explained
- Water service: the pipe from the meter to the house.
- Section testing: isolating parts of the plumbing one at a time and watching the meter to see which part is leaking.
- Slab leak: a leak in a pipe in or under a concrete floor.
- Relief valve: the safety valve on a hot water system that lets water out if pressure or temperature gets too high.
- Thermal imaging: a camera that shows heat, useful for tracing hot water pipes and leaks.
- Reroute: running a new pipe a different way instead of digging up the old one.
A typical front-yard leak, step by step
Here's how a common Pagewood leak usually plays out, so you know what to expect if we're called to one.
- The bill arrives higher than usual, and the owner does the meter test. The red numbers move with everything off.
- We arrive, confirm the meter is moving, and check the toilets, hot water relief valve and irrigation. All fine.
- We turn off the main stop tap at the house end of the water service, if there is one, or fit a temporary valve. If the meter still moves with the house isolated, the leak is in the pipe across the front yard.
- We trace the line of the pipe from the meter towards the house and listen along it. In sandy ground the sound of a leak can be faint, so we work slowly.
- Once we've found the likely spot, we dig a small hole to expose the pipe and confirm the leak.
- We look at the pipe either side. If it's sound, we repair the section. If it's old, corroded or has leaked before, we price replacing the service instead.
- With the repair done, we turn the water back on, bleed the air out and read the meter again with everything off.
Most of these jobs are finished in a single visit, and the only sign we were there is a patch of turf or a few pavers put back.
The hot water relief valve: a leak in plain sight
Every storage hot water system has a relief valve near the top and a small drain pipe that runs down to the ground or a tundish. It's meant to let out a little water as the tank heats up. If it runs constantly, or the pipe is always wet, it can waste a lot of water and point to a problem: high mains pressure, a faulty valve, or a fault in the tempering or expansion side of the system. Because the drain usually runs into a garden bed or gully, nobody notices. If yours never seems to dry out, mention it when you call. See relief valve dripping.
While you wait for us
- If the leak is inside and you can see water, turn off the main stop tap at the meter.
- Turn off the hot water system at the switchboard or set the gas unit to off if hot water is leaking.
- Move rugs, furniture and anything electrical away from the wet area.
- Take photos of the damage and the meter reading for your records and any insurance claim.
- If you can't find or turn the stop tap, don't force it. Tell us when you call.
A leak-check routine for Pagewood homes
- Every quarter: when the water bill arrives, compare it with the same time last year.
- Twice a year: do the one-hour meter test and the toilet paper test on every toilet.
- Each spring: run the irrigation zones one at a time and walk the garden looking for broken drippers or soggy spots.
- Before going away: turn the water off at the meter if the house will be empty for more than a few days.
- After any work under the house or in the front yard: read the meter with everything off to make sure nothing was damaged.
Leaks and the sand under your home
Water leaking into sand doesn't just disappear. Over months it carries fine sand away with it, and the ground around the leak can soften or settle. Under a path, that shows as a dip or a crack. Under a slab or a brick pier, it can lead to movement in the floor or cracks in the walls. That's another reason not to leave a hidden leak running once the meter test has shown one. If we find a leak has been running for a long time under paving or near the house, we'll point out any settlement we see so you can keep an eye on it after the repair.
What happens when you call
Tell us what's going on
Call or send a quick form. A photo of the problem helps us come prepared. No call-out fee.
Options and a fixed price first
We find the cause, explain your options and give you a fixed price for each before any work starts.
Fixed, tested and backed
We do the work, test it, clean up, and back our workmanship with a lifetime labour warranty.
Jobs we finished recently


Why Pagewood homeowners call us
- Based in Matraville, just down the road from Pagewood
- Rated 5.0 from 110 Google reviews
- Free quotes, with options and a fixed price before any work starts
- Lifetime labour warranty on our workmanship
- Licensed plumbers, drainers and gasfitters (Lic. 398171C)
Leak detection questions from Pagewood homeowners
How do I know if I have a hidden leak?
Turn off every tap and appliance and watch the meter for an hour. If the numbers move, water is escaping somewhere.
Why can't I see a wet patch if the leak is outside?
Pagewood's sandy ground lets water drain straight down, so a leaking pipe under the lawn often leaves no puddle.
Do you have to dig up my floor to find a leak?
No. We narrow it down by testing sections of the plumbing, then open up only the spot that needs repair.
Can you find a leak under a concrete slab?
Yes. Section testing, listening and thermal imaging tell us where it is so only a small area is opened.
Is a leak at the meter my responsibility?
No. The meter and the street side are Sydney Water's. Anything on the house side of the meter is yours.
My shower is leaking into the next room. Can you fix it?
Yes. We find whether it's the pipe, the mixer or the seals and grout, then give you options to fix it.
Could my toilet be causing a high bill?
Yes. A cistern leaking into the bowl is one of the most common silent leaks. A strip of toilet paper under the rim will show it.
My ceiling is stained but nothing is leaking in my home. What now?
It may be coming from the home above or next door. We can find the source and give you a report to pass on.
How long does leak detection take?
Simple leaks are found quickly. A slab or wall leak can take a few hours of testing.
Can you fix the leak once you've found it?
Yes. We give you a fixed price for the repair and can usually do it the same visit or book it in.
Will my insurance cover a hidden leak?
Many policies cover the damage but not always the finding or fixing of the pipe. Check your policy; we can give you a written report.
Should I replace old galvanised pipes?
If they've started leaking, usually yes. They rust from the inside and once one pinhole appears, others tend to follow.
More plumbing in Pagewood: our Pagewood plumber page, hot water, taps and toilets, blocked drains and gas fitting. Nearby: leak detection in Matraville and Malabar. Guides: Pagewood water meter leak test, hidden water leaks and buried water meters.