★★★★★ 5.0 from 100+ Google reviews · Your Sydney Plumber

Stormwater plumbing in Mascot 2020

We sort out stormwater problems in Mascot homes: water pooling around the house after rain, sand-filled pits and pipes, disconnected and overflowing downpipes, crushed or rusted kerb outlets, back yards that flood, and detention tanks that don't drain. On Mascot's low, flat blocks we measure the levels, follow the water from the roof to the street, use a camera where it helps, and give you options with a fixed price for each before any work starts. Our workmanship carries a lifetime labour warranty.

Mascot is low, flat and sandy, and that shapes everything about how rain behaves here. Stormwater has little fall to the street, so blocked pits or undersized lines leave water sitting around the house. Sand from gardens and paths washes into pits and cracked pipes and slowly fills them. And many of the older cottages and semis now have far more roof and paving draining into pipes that were built for a small house and a lot of lawn. We come over from Matraville, measure what fall you've got and fix it.

Stormwater problems we fix in Mascot

Pooling yards

New pits, grated drains and pipes to get water off flat yards and away from the house.

Pits full of sand

Pits cleaned out, and the cracked pipes letting sand in sealed or replaced.

Blocked downpipes

Downpipes cleared from gutter to pit, and broken connections repaired.

Cracked stormwater pipes

Old clay, concrete and steel lines inspected by camera and repaired or relined.

Kerb outlets

Blocked, rusted or crushed outlets replaced so water can reach the gutter.

Downpipes into the sewer

Illegal connections found and moved to the stormwater system.

Signs your stormwater isn't coping

  • Water sitting in the yard for hours after rain stops.
  • Water against the back step or under the back door in a heavy storm.
  • Pits that bubble up instead of draining.
  • Gutters overflowing at a corner even when they look clear.
  • A pit full of sand again within months of being cleaned.
  • Nothing coming out of the kerb outlet in heavy rain.
  • Damp under a timber floor after storms.
  • The overflow gully spilling in the rain, a sign stormwater is getting into the sewer.

Why stormwater struggles in Mascot

Very little fall

Stormwater pipes need slope to work. On Mascot's flat, low blocks there isn't much to work with, especially on long, narrow lots where the back of the yard is a long way from the street. Older pipes were often laid nearly flat, so water moves slowly, sand settles out, and the pipe gradually fills. When we lay new pipe, getting the best possible fall from back to front is the whole job.

Sand, everywhere

Mascot's sandy ground washes into anything it can. Open joints in old stormwater pipes let it in every time it rains, and it settles in pits, bends and the flattest sections. Cleaning helps, but unless the cracked joints are sealed or the pipe replaced, the sand comes back.

Old pipes under old homes

The workers' cottages and semis in Mascot's older streets were built with simple stormwater systems: a few downpipes into a pipe running to the street, sometimes through a side path or under the front path. Many of those pipes are now cracked clay, rusted steel or crumbling concrete. Some downpipes have been disconnected and just spill onto the ground.

More roof and paving than the pipes were built for

Over the years many Mascot homes have added rear extensions, patios, carports and concrete driveways. Every square metre of new roof or paving sends water to a system designed for a much smaller house and a lot more lawn. On flat ground, the extra water has nowhere to go but sideways.

Kerb outlets in a busy suburb

Mascot's streets get a lot of traffic and parking, and kerb outlets get driven over, crushed and filled with sand and leaves from the gutter. A blocked outlet backs up everything behind it.

Mascot homes and their stormwater

Home typeTypical systemCommon problems
Workers' cottagesDownpipes into old clay or steel pipe to the streetSand-filled pipes, disconnected downpipes, rusted outlets
SemisShared or side lines, little room down the sideWater trapped in back yards, shared pipes
Post-war brick housesClay or early PVC along the side of the houseCracked joints, roots, pits too small for added paving
Homes on the lowest blocksLong, flat runs to the streetSlow drainage, water pooling at the back
Apartments near the stationShared pits and pipes, often a detention tankBlocked shared pits, tanks not cleaned

How we fix stormwater

  1. See where the water goes. Photos or a short video in heavy rain tell us a lot. Take some next time it pours.
  2. Trace the system. We find every downpipe, pit and pipe and where each one goes.
  3. Clear and camera. We jet out sand and leaves and run a camera through to find cracks, roots, sags and broken joints.
  4. Give you options with a fixed price for each: clean and repair, reline a cracked section, replace a run, or add new pits and drains.
  5. Do the work, laying PVC at the best fall the block allows and sizing pits for the area they drain.
  6. Test it by running water through every downpipe and pit.

Quick fix or long-term fix?

ProblemQuick fixLong-term fix
Pit full of sandClean it outSeal or replace the cracked pipe letting sand in
Yard pooling at the backSweep or pump it awayA new pit and pipe at the low point
Downpipe spillingClear the blockageReplace a broken connection or undersized pipe
Kerb outlet blockedClear itReplace a crushed or rusted outlet
Water under the back doorSandbags in a stormA grated drain across the doorway, connected to the system
Downpipe into the sewerNoneReconnect it to the stormwater

What affects the cost

  • The length of pipe to clean, repair or replace.
  • What's on top: lawn, garden, pavers or concrete.
  • Access: semis and narrow side paths take more planning.
  • How many pits and downpipes are involved.
  • Relining to avoid breaking concrete.
  • Kerb and footpath work, which needs council approval.
  • Making good afterwards.

You get a fixed price for each option before any work starts.

Who's responsible?

  • You (the homeowner): gutters, downpipes, pits and pipes on your property, out to the kerb outlet.
  • Bayside Council: the street gutters, public pits and pipes, the footpath and nature strip. Work in the footpath or kerb needs their approval.
  • Sydney Water: some of the larger stormwater channels and trunk drains in the area.
  • Neighbours: water flowing from one property to another is usually for the two owners to sort out, sometimes with council.

Quick checks you can do

  1. From the ground on a dry day, look along the gutters for plants, sagging or rust.
  2. Lift each pit grate. More than a few centimetres of sand or leaves means it's due for a clean.
  3. Run a hose into each downpipe pit and see if it drains.
  4. Find your kerb outlet in the street and check it isn't blocked or crushed.
  5. Next heavy storm, walk around with an umbrella and see where water pools and which downpipes overflow.

Signs it's urgent and when it can wait

  • Call straight away if water is coming into the house or near electrics, or the overflow gully is spilling sewage in the rain.
  • Call soon if water sits against the house after every storm or a downpipe pours onto the wall.
  • Book a time if pits keep filling with sand, the yard pools, or you want the system checked before storm season.

A recent stormwater job nearby

Here's a recent stormwater job nearby in Maroubra, where a home kept flooding in heavy rain.

Flooding fixed with a new line and kerb outlet, Maroubra (nearby)

The problem: water built up against a Maroubra home and flooded its lower level every heavy storm, because the old stormwater pipe couldn't carry it away fast enough.

What we did: we dug from the existing stormwater pipe out to the street, uncovered the old pipe, which had rusted through, and connected a new PVC line. We cored through the kerb for a new outlet into the gutter and backfilled the nature strip.

The result: rain now leaves the property through the new line and outlet instead of building up against the house.

Rusted old stormwater pipe uncovered near Mascot
The old pipe, rusted through
New PVC stormwater pipe laid to the kerb near Mascot
The new line to the street

More local work is on our recent projects page.

“Best plumber in Matraville. Unblocked my drains efficiently!”

C S, Matraville (Google review)

Stormwater across Mascot, area by area

  • The older streets south of the station: the oldest systems in the suburb, with clay and steel pipes and rusted kerb outlets.
  • Semis throughout the suburb: back yards with nowhere for water to go and shared lines.
  • On the lowest, flattest blocks: where getting enough fall is the main challenge.
  • Towards Botany and Eastlakes: post-war homes where added paving has overloaded the original pipes.
  • Around the station and on former industrial land: shared pits and detention tanks that need regular cleaning.

Getting water off a flat block

On a flat Mascot block, you can't rely on the ground to move water. It has to be collected and piped. The usual approach is to work out the lowest practical point near the back of the house, put a pit there, and run a pipe to the street at the steepest fall the depth of the kerb outlet allows. Around the house, paths and patios should fall away from the walls, even slightly, with a grated drain where they meet a doorway. Where a block is so flat that a gravity pipe can't get enough fall, a small pump pit may be the answer, though it's a last resort because pumps need power and maintenance. We'll measure levels on site and tell you what will actually work.

Semis and back yards

Many Mascot semis and cottages have a small, paved back yard with walls or fences on three sides. When it rains hard, the yard fills, and the original drainage, often a single small pit, can't keep up. Common fixes are a larger pit, a silt pit ahead of the line, a grated drain across the back door and a new pipe along the side of the house to the street. Where the pipe has to run under a timber floor, we plan the route to keep the fall and leave access for cleaning.

Detention tanks on newer homes

Some newer Mascot homes and townhouses were built with an on-site detention tank or pit, which holds water in heavy rain and lets it out slowly through a small outlet. It only works if it's kept clean. Leaves and silt block the outlet screen, the tank fills, and it overflows into the yard. If your home has one, have it inspected and cleaned regularly. Don't remove or change it without checking with Bayside Council, as it's usually a condition of the home's approval.

Downpipes connected to the sewer

In some older Mascot homes, a downpipe or a yard drain was connected to the sewer. In heavy rain it floods the sewer and can push sewage out of your overflow gully or a neighbour's. It isn't allowed. We find these with a dye test or camera and reconnect them to the stormwater. See downpipes into the sewer.

Gutters and leaf guards

A lot of stormwater trouble starts at the gutter. Leaves block the outlet, the gutter overflows along the fascia, and water drops straight down beside the wall, where it soaks under the floor. Mascot's street trees and garden trees drop plenty of leaves, so clean gutters before storm season and after the autumn drop. Leaf guards help but still need checking. Where a downpipe meets the ground, make sure it's still connected to the pit below and hasn't been knocked loose.

Before you pave or build

Planning a new driveway, patio, carport or extension? On a flat Mascot block, decide where the rain will go before the concrete is poured. Pits at the low points, falls away from the house, and pipes big enough for the new roof and paved area are cheap to include now and expensive to add later. See stormwater pit installation and backyard drainage.

What to photograph in the rain

  • Which gutter corners overflow.
  • Downpipes spilling at the joint or not draining at the pit.
  • Where water pools, how deep, and how long it stays.
  • The kerb outlet: is water coming out?
  • Water coming onto your block from next door or the street.

A stormwater care calendar

  • Late spring: clean gutters and every pit before storm season.
  • After big storms: check pits and the kerb outlet for sand and leaves.
  • Autumn: clean gutters again after the leaves drop.
  • Every year or two: camera the main line if pits keep filling with sand.
  • Whenever you add paving: plan where the water will go.

Stormwater words explained

  • Downpipe: the vertical pipe from the gutter to the ground.
  • Pit: a box in the ground with a grate that collects water.
  • Kerb outlet: where your stormwater comes out into the street gutter.
  • Fall: the slope a pipe or surface needs for water to run.
  • Grated drain: a long, narrow drain with a grate across a doorway, driveway or patio.
  • On-site detention: a tank or pit that holds stormwater and releases it slowly.
  • Pump pit: a pit with a pump, used where gravity can't move the water.

The kerb sets the depth

On a flat block, the kerb outlet decides how deep your stormwater pipe can be at the street end, and that decides how much fall you can get back to the house. A standard kerb outlet sits only a short way below the top of the kerb, so the pipe has to rise gently from there all the way to the back of the block. On a long Mascot lot that doesn't leave much room. That's why some older systems were laid almost flat and why they silt up. When we redesign a system, we measure the kerb, the ground at the back and every point in between, then choose pipe sizes and pit positions that make the most of the fall available. Sometimes two outlets, or a pipe to a side street on a corner block, gives a better result than one long run.

Stormwater and the subfloor

Mascot's older cottages and semis often have a timber floor only a little above the ground outside. When downpipes spill beside the walls or the yard slopes towards the house, water soaks under the floor after every storm. Over time that rots bearers and joists, rusts the base of the brickwork and leaves the house smelling musty. Fixing it usually means reconnecting downpipes, adding a pit or two near the house, and making sure paths and garden beds slope away from the walls. Clearing the subfloor vents so air can move helps everything dry out.

Rainwater tanks on small blocks

Even a slimline tank along a side fence takes some roof water out of the stormwater system and gives you water for the garden or toilets. On Mascot's smaller blocks, that can take a little pressure off old pipes in a storm. The tank's overflow still needs to connect to the stormwater properly, not pour onto the ground beside the house or over the fence. Keep the first-flush device and the inlet screen clean so the tank doesn't fill with leaves.

Mascot's ground and water

Mascot is built on the Botany Sands, deep sand with groundwater close to the surface. The same flat, sandy, low-lying ground that once fed Sydney's early water supply makes stormwater hard to move today. Water doesn't run off quickly, sand gets into every open joint, and on the lowest blocks the ground can already be wet after a run of storms. Groundwater under parts of Mascot is also contaminated, and the NSW Government restricts using it from backyard bores, so a rainwater tank is the better way to water the garden. Good pipes, enough fall and clean pits matter more here than in hillier suburbs.

Replacing an old stormwater line, step by step

  1. We camera the old line and mark its route and depth.
  2. We measure levels from the back of the house to the kerb to work out the best fall.
  3. We agree the plan and fixed price with you, including where new pits go.
  4. The old pipe is dug out or abandoned in place, and new PVC is laid on a bed of sand at the planned fall.
  5. Downpipes are reconnected with new fittings, and new pits are set at the low points.
  6. If the kerb outlet is being replaced, council approval is arranged and the outlet fitted.
  7. We run water through the whole system, backfill and reinstate the yard.

On a typical Mascot cottage block this is a one to two day job, depending on length and what's on top.

Corner blocks and rear lanes

Some Mascot homes sit on a corner or back onto a lane. That can be good news for drainage. A pipe to the side street or the lane may be much shorter than one to the front kerb, with more fall over that distance. Whether you can discharge that way depends on what's there and on Bayside Council's requirements, so we check before designing anything. On homes that already drain to a lane, the outlet there is often the forgotten part of the system and worth checking for sand and leaves.

What happens when you call

1

Tell us what's going on

Call or send a quick form. A photo of the problem helps us come prepared. No call-out fee.

2

Options and a fixed price first

We find the cause, explain your options and give you a fixed price for each before any work starts.

3

Fixed, tested and backed

We do the work, test it, clean up, and back our workmanship with a lifetime labour warranty.

Jobs we finished recently

Jetting a blocked drain in Maroubra
Jetting a blocked drain in Maroubra
Overflowing gully cleared in Little Bay
Overflowing gully cleared in Little Bay

See more recent projects

Why Mascot homeowners call us

  • Based in Matraville, a short drive from Mascot
  • Rated 5.0 from 110 Google reviews
  • Free quotes, with options and a fixed price before any work starts
  • Lifetime labour warranty on our workmanship
  • Licensed plumbers, drainers and gasfitters (Lic. 398171C)

Stormwater questions from Mascot homeowners

Why does my yard flood when it rains?

On Mascot's flat blocks water has little slope to run away, and old pipes are often full of sand or too small. A pit and pipe at the low point usually fixes it.

Why do my pits keep filling with sand?

Sand washes into the pipe through cracked joints. Sealing or replacing the damaged section stops it.

Who looks after the kerb outlet?

Your pipe and outlet are yours. The gutter and footpath are Bayside Council's, and work there needs approval.

Can you fix water coming under my back door?

Yes. A grated drain across the doorway connected to the stormwater, and paving that falls away from the door, usually fixes it.

Is it legal to connect downpipes to the sewer?

No. They must go to the stormwater system. We can find and reconnect them.

Do I need a pump for my stormwater?

Rarely. Most Mascot blocks can drain by gravity with careful levels. A pump is a last resort.

Can a stormwater pipe be relined?

Yes. It seals cracked joints so sand and roots can't get in, without digging.

My back yard floods every storm. What can be done?

A larger pit, a silt pit, a grated drain at the door, and a pipe along the side to the street are the usual fixes.

How often should I clean my pits?

At least once a year before storm season, and after big storms.

Does my detention tank need maintenance?

Yes. The outlet and screen block with leaves and silt. Have it inspected and cleaned regularly.

How long does a stormwater repair take?

A clean and small repair is often a few hours. A new line to the kerb can take a day or two.

Will you put my lawn and paving back?

Yes. We backfill, relay pavers and leave the area tidy.

More plumbing in Mascot: our Mascot plumber page, blocked drains, pipe relining and leak detection. Nearby: stormwater in Botany and Pagewood. Guides: stormwater plumbing, backyard drainage and blocked downpipes.

Call 0401 758 373Free quote