Tap repairs in Chifley 2036
A dripping tap rarely fixes itself, and in a busy family home it only gets worse. In Chifley, we repair the washer taps that are still in many older cottages, the mixers in newer family homes and townhouses, and everything in between. We recently supplied and fitted a new kitchen mixer for a Chifley household, one of the most common tap jobs we do. Most tap repairs are done in one visit with parts from the van. We're a few minutes away in Matraville.
Tap repairs we do
Dripping washer taps
New washers and re-cut seats so the tap shuts off cleanly.
Leaking mixers
Cartridges, O-rings and seals replaced, or the mixer replaced.
New kitchen mixers
Mixers supplied and fitted to suit your sink and benchtop.
Shower taps and mixers
Spindles and cartridges replaced from the front, usually without removing tiles.
Laundry and garden taps
Seized, dripping and rusted taps repaired or replaced.
Stiff or loose handles
Spindles, cartridges and handle fixings replaced.
Signs a tap needs repair
- Drips from the spout after it's turned off.
- Water at the handle or around the base.
- Hard to turn, or needs a lot of force to stop.
- Spins without stopping the water.
- Squeals or shudders when turned on.
- Low flow or a spluttering stream.
- A loose handle or lever.
- Damp in the cupboard under a sink or vanity.
Why taps fail in Chifley homes
Washer taps in older cottages
Traditional washer taps close by pressing a rubber washer onto a brass seat. Over the years, the washer hardens and the seat wears a groove. A new washer on a worn seat drips again soon, which is why we re-cut the seat as part of the repair. Many of Chifley's older cottages still have washer taps in the bathroom, laundry and garden.
Mixers in busy kitchens
Chifley has a larger share of families with children than many nearby suburbs, and kitchen mixers in family homes get heavy use. After 10 to 15 years, the cartridge wears and the mixer drips or gets stiff. Pull-out spray mixers also have a hose under the sink that can crack.
Imported fittings in newer homes
Many of the larger homes that have replaced Chifley's cottages have imported mixers. Some use cartridges that are specific to the brand and hard to find. Knowing the brand and model helps us bring the right parts.
Old pipes and grit
In older homes with some original galvanised pipe, rust and grit wash through and wear washers, seats and cartridges faster. See galvanised pipes.
Water pressure
High pressure wears washers and cartridges faster and can make taps bang when they shut. A pressure limiting valve protects every tap in the home.
Chifley homes and their taps
| Home type | Typical taps | Common faults |
|---|---|---|
| Older cottages | Washer taps throughout, some updated mixers | Worn seats, rusted garden taps, stiff spindles |
| New family homes | Imported mixers, wall-mounted shower mixers, several bathrooms | Cartridges, hard-to-find parts |
| Townhouses and duplexes | Mixers in kitchens and bathrooms | Cartridges, hoses, leaks to the floor below |
| 1960s unit blocks | Mix of washer taps and mixers | Worn seats, dripping mixers, seized valves |
How we repair a tap
- Ask what's happening, and for a photo and any brand name.
- Turn off the water at the isolating valve or meter.
- Take the tap apart and find the worn part.
- Give you options: repair, convert or replace, each with a fixed price.
- Repair it properly: re-cut seats, new washers, O-rings, spindles or cartridges.
- Test it for drips, leaks and smooth operation.
Repair, convert or replace?
| Situation | Usually best |
|---|---|
| Washer tap with a sound body | Repair with a new washer and re-cut seat |
| Washer taps you'd like easier to use | Convert to quarter-turn ceramic spindles |
| Mixer dripping, cartridge available | New cartridge |
| Mixer with no parts available | Replace the mixer |
| Corroded or cracked tap body | Replace the tap |
What affects the cost
- The type of tap and whether parts are available.
- How many taps are done in one visit.
- Access: shower mixers behind tiles, tight vanities.
- Isolation: whether there are working isolating valves.
- New tapware: depends on the model.
You get a fixed price before any work starts.
Who's responsible?
- You: taps, mixers and isolating valves in your home.
- Owners corporation: shared pipes and common-area taps.
- Sydney Water: the supply up to the meter.
Signs it's urgent and when it can wait
- Call straight away if a tap won't turn off, or water is leaking into a wall or the floor below.
- Call soon if a shower mixer leaks behind the tiles or a tap leaks at the base into the cupboard.
- Book a time if a tap drips or is stiff.
A recent tap repair nearby
Here's a recent tap repair nearby in Maroubra, done on the same visit as a drain clear.
Leaking taps fixed during a drain clear, Maroubra (nearby)
The problem: a Maroubra home had leaking taps as well as slow drains.
What we did: we laid a mat to protect the floor, jetted the drains and floor wastes clear, and then repaired the leaking taps on the same visit.
The result: the taps shut off properly and the drains flow freely, all in one visit.


“Great plumber, fixed my leaking taps quickly and at a great price!”
Tom (Google review)
More local work is on our recent projects page.
Tap repairs across Chifley
- Around Mawson Parade and Dr Walters Park: washer taps in older cottages, mixers in rebuilt homes.
- Along Anzac Parade: units with a mix of tap types.
- Near Chifley Public School: busy family kitchens and bathrooms.
- The Little Bay side: newer homes with imported mixers.
- The Matraville side: older streets with original taps and garden taps.
New kitchen mixers
Replacing a worn kitchen mixer is one of the most common tap jobs we do in Chifley, including one we supplied and fitted recently. A new mixer stops the drip and the stiff lever, and lets you choose a style that suits the kitchen: a gooseneck, a pull-out spray or a simple lever. Check the tap hole size and the benchtop thickness, and pick a solid brass body from a brand with local spare parts. We can supply the mixer or fit one you've bought, and we'll replace old hoses and isolating valves at the same time so the whole connection is new. If you'd like filtered water too, a filtered mixer can go in the same hole. See water filters in Chifley.
Bathroom basin taps
Basin taps sit in a damp, soapy room. Washer-type pillar taps in older bathrooms get stiff as soap and limescale build up around the spindle. Vanity mixers in updated bathrooms have a smaller cartridge that wears in the same way as a kitchen mixer. A leak at the base often runs down inside the vanity and swells the cabinet floor before anyone notices, so check inside the cupboard if you see water around the tap.
Shower taps and mixers
Shower taps can cause hidden damage. The tap bodies sit inside the wall, and if a spindle O-ring or cartridge seal fails, water can leak into the wall every time the shower runs. Signs include damp skirting boards on the other side of the wall, loose tiles, mould along the grout or a musty smell. A dripping shower rose usually means a worn washer or cartridge. Most repairs are done from the front without removing tiles. See leak detection in Chifley if you suspect a hidden leak.
Laundry taps
Laundry taps are often the oldest in the home and are left open for years to supply the washing machine. When you finally turn them off, they're stiff, seized or start dripping. Washing machine hoses are under pressure all the time and can burst. A single-lever machine tap that turns off hot and cold together makes it easy to shut off the machine when you go away.
Garden and outdoor taps
Outdoor taps sit in the weather, and the pipes that feed them often rise straight out of the ground. In older Chifley homes, those risers are often galvanised steel that has rusted at ground level. A garden tap that wobbles when you turn it, or leaks at the base, may be close to breaking. We replace the tap and riser with copper and fix it securely.
Washer taps: repair them properly
The most common reason a washer tap keeps dripping is that only the washer gets changed. Water and grit wear a groove into the brass seat, and a new washer can't seal against it. A proper repair re-cuts the seat so it's smooth and flat again, fits a new washer, and replaces the spindle O-rings while the tap is open. Done properly, a washer tap repair lasts for years.
Converting to quarter-turn
Ceramic disc conversion spindles turn traditional washer taps into quarter-turn taps. They replace the spindle inside the tap body, so the handles and bodies stay the same, with no change to the tiles or basin. Quarter-turn taps shut off with a light touch and drip far less. They're easier for small children and older family members to use.
Choosing new tapware
- Match the holes: one, two or three holes in the basin, sink or benchtop.
- Choose solid brass: it lasts longer than cheaper materials.
- Pick a brand with local parts: it makes future repairs quicker.
- Check the water rating: a good WELS rating saves water.
- Think about the users: lever handles are easier for children and older hands.
Low flow at a tap
If one tap has low flow while others are fine, the cause is usually at that tap: a blocked aerator, a partly closed isolating valve or a worn cartridge. Unscrewing and rinsing the aerator often fixes it. If every tap has low flow, the cause is further back: the meter valve, a pressure problem, or old galvanised pipes narrowing inside. We check from the tap back so we find the real cause.
Dripping taps and your water bill
A single dripping tap runs every minute of every day. Over a year, a steady drip can add up to thousands of litres. A dripping hot tap is worse, because you're also paying to heat the water that goes down the drain. Fixing drips early also protects the tap, as the longer a washer tap drips, the deeper the groove it wears in the seat.
Taps that bang or shudder
If a pipe bangs when you turn a tap off quickly, that's water hammer: a pressure wave travelling through the pipes when the flow stops suddenly. It's most common with quarter-turn taps, mixers and washing machine valves that close fast. A tap that shudders while running usually has a loose washer or worn spindle. We check the tap first, then the pipe clips and the water pressure. See water hammer.
Hot taps that run cold, or cold taps that run warm
If a mixer gives warm water when set to cold, the cause is often a worn cartridge letting hot and cold cross over. If the hot takes a long time to reach a tap, it may be a long pipe run from the hot water system, which is common in larger Chifley homes with bathrooms far from the unit. We check the mixer first. If the problem is at the hot water system or tempering valve, see hot water in Chifley.
Isolating valves under the sink
Isolating valves let you turn off one tap without shutting off the whole home. In many older Chifley homes, they were never fitted or have seized. When a tap needs repair and there's no working valve, the water has to go off at the meter. We replace seized valves, or fit new ones, as part of a tap repair.
Taps in townhouses and units
In a townhouse or unit with a home below, a leak at the base of a basin tap or a shower mixer leaking inside the wall can reach the ceiling underneath. If a neighbour mentions a stain, check the taps and cupboards for damp, and look for loose tiles or damp grout around the shower. If you can't see the cause, call us and we'll find it.
Getting ready for our visit
- Take a photo of the tap and any brand name on it.
- Clear the cupboard under the sink or vanity.
- Know where your meter is.
- Tell us about access: gates, dogs, stairs and parking.
- List every tap you'd like looked at, so we bring the right parts.
Looking after your taps
- Don't over-tighten washer taps.
- Rinse aerators every few months.
- Turn isolating valves off and on once a year so they don't seize.
- Clean around spindles and bases with a mild cleaner.
- Turn off garden taps fully after use.
- Fix drips early, before they wear the seat badly.
What to expect on the day
We give you a time window and let you know when we're on the way. Most tap repairs are done in one visit with parts from the van. We protect your floor and benchtop, turn off the water, take the tap apart and show you the worn parts. Once it's repaired, we test it, check for leaks and make sure it turns smoothly.
Taps for every age
In a family home, the same taps are used by toddlers and grandparents. Stiff washer taps are hard for small hands and sore fingers. Lever mixers and quarter-turn taps need only a light push. A lever on the kitchen mixer, quarter-turn conversions in the bathroom and a single-lever washing machine tap in the laundry make daily life easier. Pairing new taps with a tempering valve on the hot water reduces the risk of scalds at the bathroom taps, which matters with young children. See tempering valve installation.
Taps in rarely used bathrooms
Newer Chifley homes often have a guest bathroom or ensuite that's rarely used. Taps and mixers that sit for weeks can stiffen, and washers and O-rings can dry out. Running each tap for a few seconds every week or two keeps the seals working and the traps full. If a rarely used tap starts dripping or leaking at the base, get it seen to before it damages the vanity.
Why our tap repairs last
We repair taps the way they should be repaired: re-cut seats instead of just swapping washers, quality washers and O-rings, cartridges that match the original, and clean, lubricated spindles so the tap turns smoothly. We test every tap before we leave. Our labour is covered by a lifetime warranty, so if a tap we repaired starts dripping again because of our work, we come back and fix it.
Why Chifley homeowners call us
We're a few minutes away in Matraville and do tap work in Chifley homes regularly, from washer tap repairs in older cottages to new kitchen mixers in family homes. You get options and a fixed price before any work starts. If something is dripping, send us a photo and we'll tell you the likely fix before we arrive.
Pull-out and spray mixers
Pull-out and pull-down kitchen mixers are popular in Chifley's newer kitchens. The spray head is connected to a flexible hose that runs down through the mixer body and loops under the sink, usually with a small weight to pull it back. Over time, the hose can crack or wear where it rubs, the head can stop retracting, or the spray button can stick. Water dripping into the cupboard when the tap is running often means the hose has split. We can usually replace the hose or spray head on its own if parts are available, or replace the mixer if they're not. A photo of the brand mark helps us check before we come.
Wall-mounted bath and shower mixers
Wall-mounted mixers in newer bathrooms sit on a body inside the wall, with the cartridge accessed from the front. When they drip or stiffen, a new cartridge usually fixes it. If the body itself is leaking inside the wall, that's a bigger job, and we'll explain the options before anything is opened.
Tap words explained
- Washer: the rubber disc that seals a traditional tap.
- Seat: the brass ring inside the tap body that the washer closes on.
- Spindle: the part that turns when you turn the handle.
- Cartridge: the unit inside a mixer or quarter-turn tap that controls the water.
- O-ring: a small rubber ring that seals around the spindle.
- Aerator: the screen at the end of the spout.
- Isolating valve: a small valve under the sink that turns off water to one tap.
What happens when you call
Tell us what's going on
Call or send a quick form. A photo of the problem helps us come prepared. No call-out fee.
Options and a fixed price first
We find the cause, explain your options and give you a fixed price for each before any work starts.
Fixed, tested and backed
We do the work, test it, clean up, and back our workmanship with a lifetime labour warranty.
Jobs we finished recently


Why Chifley homeowners call us
- Based in Matraville, a few minutes from Chifley
- Rated 5.0 from 110 Google reviews
- Free quotes, with options and a fixed price before any work starts
- Lifetime labour warranty on our workmanship
- Licensed plumbers, drainers and gasfitters (Lic. 398171C)
Tap repair questions from Chifley homeowners
Why does my tap still drip after a new washer?
The seat is usually worn. We re-cut it as part of the repair.
Can you supply and fit a new kitchen mixer?
Yes, or fit one you've bought.
Can you fix a dripping mixer?
Usually, with a new cartridge.
Can you repair a shower tap without removing tiles?
In most cases, yes, from the front.
Can washer taps be converted to quarter-turn?
Often, with ceramic disc spindles.
Why is my tap so stiff?
A worn spindle, a dry O-ring or a failing cartridge.
Can you fix my garden tap?
Yes, and replace a rusted riser if needed.
Do I need to turn off all the water?
Only without a working isolating valve. We can fit one.
Can you get parts for imported mixers?
Often. The brand and model help us find them.
How long does a tap repair take?
Most take under an hour.
Can you do several taps in one visit?
Yes, which saves another call-out.
What warranty do I get?
Our workmanship carries a lifetime labour warranty.
More plumbing in Chifley: our Chifley plumber page, taps and toilets, toilet repair and water filters. Nearby: tap repair in Little Bay, Malabar and Matraville. Guides: mixer tap leaking and ceramic disc vs washer taps.