★★★★★ 5.0 from 100+ Google reviews · Your Sydney Plumber

Tap repairs in Little Bay 2036

We repair and replace taps in Little Bay homes: dripping washer taps in the post-war houses, worn cartridges in the mixers of the newer homes on the old hospital site, outdoor showers and garden taps corroded by the sea air, laundry and washing machine taps, and leaks under sinks. We find why it's leaking, give you options to repair or replace with a fixed price before any work starts, and back the work with our lifetime labour warranty.

Little Bay taps have a coastal life. Outside, the sea air off the Tasman works on every brass fitting and chrome handle, and the outdoor showers people use after a swim at Little Bay Beach or the rock pool get sand in them year round. Inside, the 1950s homes on War Ballot blocks often still have washer taps, while the newer homes built on the former Prince Henry Hospital site have mixers now 15 to 20 years old. Each fails in its own way. We're based in Matraville, just up the road.

Tap problems we fix in Little Bay

  • Drips from the spout after the tap is turned off.
  • Leaks around the handle or lever.
  • A mixer that drips or won't hold temperature.
  • Outdoor showers that drip, seize or have lost pressure.
  • Garden taps that are corroded, stiff or snapped.
  • Weak flow from one tap.
  • Leaks under the sink at hoses or valves.
  • Banging when taps close.

Why taps wear out in Little Bay

Sea air on outdoor fittings

Little Bay faces the ocean, and salt settles on every outdoor tap and shower. The spindle corrodes, the washer bonds to the seat, the handle seizes, and eventually the tap won't turn off fully or snaps when forced. Homes nearest the beach and the headlands see it most.

Sand in outdoor showers

Outdoor showers used after the beach take a steady dose of sand. It gets into the mixer cartridge and the shower rose, wearing the sealing surfaces and blocking the outlet.

Washer taps in post-war homes

Many of the homes built on Little Bay's War Ballot land in the 1950s still have washer taps in the laundry, bathroom and garden. The washer hardens and the seat wears a groove, so the tap drips however hard it's turned. We re-cut the seat when we repair it.

Mixers on the hospital site

Homes built on the former hospital site since the early 2000s have single-lever mixers throughout. At 15 to 20 years old, many cartridges are wearing out. Some are brand-specific, so we identify the model before ordering parts.

Water pressure

High mains pressure wears washers and cartridges faster and makes taps bang. A pressure limiting valve at the meter helps.

Taps in different Little Bay homes

Home typeTypical tapsCommon faults
Post-war War Ballot homesWasher taps in laundries and bathrooms, old garden tapsWorn seats, stiff spindles, corroded outdoor taps
Homes near the beachOutdoor showers and garden tapsSalt corrosion, sand in mixers
Houses on the hospital siteMixers throughoutWorn cartridges, O-rings
TownhousesMixers with isolating valvesCartridges, hose leaks
ApartmentsImported mixersBrand-specific cartridges, leaks to the unit below

How we repair taps

  1. Turn off the water at the isolating valve, or at the meter.
  2. Take the tap apart and check the washer, seat, cartridge and O-rings.
  3. Give you options to repair or replace, each with a fixed price.
  4. Repair or replace with parts that suit the tap and, outside, the coast.
  5. Clean the aerator or shower rose.
  6. Test it through its full range and check for leaks.

Washer tap repairs

New washers and O-rings, and worn seats re-cut.

Mixer repairs

Cartridges replaced with the correct part.

Outdoor shower repairs

Mixers serviced or replaced, roses cleared, pipework checked.

Garden taps

Corroded and seized outdoor taps replaced with solid brass.

Laundry taps

Old laundry and machine taps replaced with quarter-turn valves.

Isolating valves

Fitted so taps can be turned off individually.

Repair or replace?

ProblemUsually a repairUsually a replacement
Washer tap drippingNew washer and re-cut seatCorroded body
Mixer drippingNew cartridgeCartridge no longer made
Outdoor tap seized by saltRarely worth itYes, solid brass
Outdoor shower drippingNew cartridgeCorroded mixer
Leak at the handleNew O-ringsBroken body

What affects the cost

  • The tap and whether parts are available.
  • How many taps in one visit.
  • Seized fittings outside that need care to remove.
  • Access: tight cabinets, taps behind tiles.
  • A new tap: depends on the model.

You get a fixed price before any work starts.

Who's responsible?

  • You: taps and pipes on the house side of the meter.
  • Sydney Water: the meter and the main.
  • Townhouses and apartments: taps in your home are yours; shared pipes are the owners corporation's.

Quick checks you can do

  1. Spout or handle? Drips from the spout mean washer or cartridge; water at the handle means O-rings.
  2. Weak flow? Unscrew the aerator or shower rose and rinse out sand.
  3. Outdoor taps: if one is stiff, don't force it.
  4. Under the sink: look for damp or rusty hoses.
  5. Isolating valves: check they turn.

See our dripping taps guide.

Signs it's urgent and when it can wait

  • Call us soon if a tap won't turn off, has snapped, or is leaking into a wall or cabinet.
  • Book a time if it drips or is stiff.
  • Mention it next visit if it's a little noisy.

A recent tap repair nearby

Here's a recent tap repair nearby in Maroubra.

Leaking taps fixed on the same visit as a drain clear, Maroubra (nearby)

The problem: a Maroubra home had leaking taps as well as slow, blocked drains.

What we did: we laid a mat to protect the floor, jetted the drains and floor wastes, and repaired the leaking taps before we left.

The result: the taps shut off properly and the drains run freely, without a second visit.

Floor protected during tap and drain work near Little Bay
Floor protected, Maroubra
Drain jetting on the same visit as tap repairs near Little Bay
Drains cleared on the same visit

“Great plumber, fixed my leaking taps quickly and at a great price!”

Tom (Google review)

More local work is on our recent projects page.

Taps across Little Bay, area by area

  • Near Little Bay Beach and the rock pool: outdoor showers and garden taps in the strongest sea air.
  • Towards Henry Head: exposed blocks where even sheltered taps corrode.
  • The older War Ballot streets: washer taps and old laundries.
  • The former Prince Henry Hospital site: mixers due for new cartridges.
  • Around the golf courses: homes with several garden taps.

Outdoor showers after the beach

An outdoor shower is one of the joys of living near Little Bay Beach. It's also the hardest-working tap on the property: salt on the outside, sand on the inside, and long quiet spells over winter. To keep it working, rinse salt off the mixer with fresh water, run it through winter so the valve doesn't seize, and unscrew the rose now and then to rinse out sand. When the mixer starts to drip or lose pressure, a new cartridge often fixes it. If the body has corroded, we replace it with a mixer suited to coastal conditions.

Garden taps that snap

Garden taps in Little Bay's sea air can corrode so badly that they snap when turned. If a tap is stiff, don't force it, especially if it's on an old galvanised riser. A snapped tap sprays at full mains pressure until the water is turned off at the meter. We replace corroded taps and risers with solid brass, fixed firmly, and can add a vacuum breaker so garden water can't be drawn back into the house pipes.

Washer taps in older homes

If your 1950s Little Bay home still has washer taps and you like them, they don't have to go. A proper repair with a re-cut seat stops the drip for years. Or ceramic disc conversion spindles can turn them into quarter-turn taps that drip far less, without changing the tap bodies or disturbing tiles.

Mixers on the hospital site

Mixers in the newer Little Bay homes are reaching the age where cartridges wear out. The usual signs are a drip from the spout, a stiff lever, or a lever that has to be pushed hard to stop the flow. Cartridges are often specific to the brand and model, so a photo of the mixer and any brand name helps us bring the right part.

Kitchen sink leaks that aren't the tap

Water under a kitchen sink could be the mixer, the hoses, an isolating valve, the dishwasher connection or the sink waste. We dry everything, run water, and watch each connection until we find the one that's weeping.

Laundry taps

Little Bay laundries often have old tub taps and washing machine taps that haven't been turned in years. Replacing them with a tub mixer and quarter-turn machine valves, plus new machine hoses, fixes several worn parts in one visit.

Choosing a new tap

  • Match the holes in your sink or basin.
  • Choose solid brass, especially outside near the coast.
  • Check the WELS rating.
  • Pick a brand with local spare parts.
  • Consider filtered water in the kitchen.

A tap care checklist

  • Rinse salt off outdoor taps and showers with fresh water.
  • Turn outdoor taps on and off monthly so they don't seize.
  • Rinse aerators and shower roses every few months.
  • Turn isolating valves off and on once a year.
  • Look under sinks for damp.
  • Turn washing machine taps off when you go away.

What to expect on the day

We give you a time window and let you know when we're on the way. Most repairs are done in one visit with parts from the van. If a cartridge needs ordering, we come back. We protect benchtops and floors and point out other taps close to needing attention.

Tap words explained

  • Washer: the rubber disc that seals against the seat.
  • Seat: the brass ring inside the tap.
  • Cartridge: the unit inside a mixer.
  • Aerator: the screen at the end of the spout.
  • Rose: the head of a shower.
  • Vacuum breaker: a fitting that stops hose water flowing back into the pipes.

Replacing an outdoor shower mixer, step by step

  1. We turn off the water and check how the shower is fed: from the hot water system, a separate outdoor supply, or a mixer on the wall.
  2. The old mixer or taps are removed carefully, because corroded fittings can snap and take the pipe in the wall with them.
  3. We check the pipe behind for corrosion and replace any section that's thin or pitted.
  4. The new mixer, suited to coastal conditions, is fitted and sealed to the wall.
  5. We fit or clean the shower rose and check the flow and temperature.
  6. Exposed pipework is clipped firmly and protected where possible.

Fixing a dripping washer tap properly

  1. Isolate the water and drain the tap.
  2. Remove the handle and cover without scratching the chrome.
  3. Unscrew the spindle and remove the jumper and washer.
  4. Check the seat. If it's pitted, re-cut it smooth.
  5. Fit a new washer, jumper and O-rings, or a ceramic disc conversion.
  6. Reassemble and test several times.

The re-cut seat is the step most quick fixes skip, and why some taps start dripping again soon after a new washer.

Replacing a mixer cartridge

  1. Turn off the isolating valves.
  2. Remove the lever cap, grub screw and lever.
  3. Unscrew the retaining nut and lift out the old cartridge.
  4. Match its size and markings, and check the seats below.
  5. Clean out any sand or grit, which is common this close to the beach.
  6. Fit the new cartridge, reassemble, and test through the full range.

Easier taps for long-term residents

Little Bay has many long-term residents in its older homes. Stiff cross-head taps get harder to turn with age. Lever handles, quarter-turn spindles and single-lever mixers are much easier, and most fit the existing holes. A tempering valve keeps hot water at a safe temperature in the bathroom. Ask us when we're fixing a tap. See tempering valve installation.

Going away?

Before a trip, turn off the washing machine taps and check under each sink. Turn outdoor taps fully off and disconnect hoses with trigger nozzles. If the home will be empty for a while, turn the water off at the stop tap.

What a drip costs

A drip runs day and night. Over a quarter it shows on the bill, plus sewer usage. A dripping hot tap wastes the energy used to heat it. Drips stain basins and usually get worse. Fixing it early is cheapest.

When the tap is a sign of something bigger

Several taps failing at once, brown water in an older home, banging in the walls or low pressure everywhere can point to old galvanised pipe, high pressure or corroded outdoor pipework. If we see signs like that, we'll tell you and give you a separate fixed price.

Shower mixers behind tiles

Inside, shower mixers sit in the wall sealed against the tiles. If the cartridge wears, the shower drips. If the body or its connections leak, water goes into the wall every time someone showers. Watch for loose tiles, dark grout, mould at the base of the wall or damp in the next room. New grout won't fix water coming from behind. See leak detection in Little Bay.

Hot taps that run cold or too hot

If a hot tap takes a long time to warm up, runs lukewarm or scalds, the tap usually isn't the problem. It may be the hot water system, a tempering valve, or, with continuous flow, the unit cycling at low flow. We check the hot water side too. See hot water in Little Bay.

Hose taps and hose reels

Hose reels mounted beside a garden tap put strain on it every time the hose is pulled. On an old galvanised riser, that eventually snaps the riser at the base. If your garden tap wobbles or the riser is rusty at ground level, replace it before it breaks. A wall-mounted reel fixed separately from the tap takes the strain off.

Why Little Bay taps need more care

In most suburbs, a garden tap can be ignored for years. In Little Bay, the sea air means outdoor taps and showers need a little attention: a fresh-water rinse now and then, regular use so they don't seize, and replacement with coastal-suited fittings when the time comes. Inside, the age of the homes decides what fails: washer seats in the older houses, cartridges in the newer ones. Knowing which you have makes the repair quicker and more reliable.

Isolating valves under sinks

Older Little Bay homes often have no isolating valves under sinks and basins, so the water has to go off at the meter to repair a tap. Newer homes have them, but after 15 to 20 years many have seized. We fit or replace isolating valves while we're there, so next time one tap can be turned off on its own.

Before you call

  • Which taps are playing up, and what are they doing?
  • Is there a brand name on the mixer?
  • Inside or outside?
  • Are there isolating valves under the sink, and do they turn?
  • A photo helps us bring the right part.

Pull-out kitchen mixers

Pull-out kitchen mixers are common in updated Little Bay kitchens. The hose inside can leak in the cabinet, the spray head can drip or stick between modes, and the counterweight can slip so the head won't retract. Most of these parts can be replaced on their own, so the whole mixer doesn't need to go.

Filtered water taps

When a kitchen tap is being replaced, many owners add filtered drinking water: a separate filter tap beside the mixer, or a mixer with a built-in filtered outlet. The filter cartridge sits under the sink and needs room and easy access. We'll check the space and whether a second tap hole is possible. See water filters in Little Bay.

Why the same tap keeps failing

If a tap has been repaired before and drips again within months, something is wearing it: sand or grit getting into the cartridge, high pressure, or a cheap replacement part that wasn't a true match. We find which before fitting another part, so the repair lasts.

Tapware for the coast

When you're choosing new outdoor taps or a new outdoor shower in Little Bay, look for solid brass bodies with a good-quality finish rather than plated zinc, and parts that can be serviced. Some finishes hold up far better than others in salt air. We can recommend options we've seen last near the coast.

Bath taps and spouts

Older Little Bay bathrooms often have separate bath taps and a wall spout, sometimes with a shower diverter. A spout that drips after the shower is used can be the diverter, not the taps. Bath taps that drip into the bath are easy to ignore but waste water like any other. We check how the bath and shower are set up and fix the part that's actually at fault.

Keeping the character of an older home

Owners of the older Little Bay homes sometimes want taps that suit the house. Traditional-style cross-handle taps and bath sets are still made with modern ceramic internals that don't drip. If the original tap bodies are sound, we can often replace just the internals and keep the look.

Grit after mains work

When Sydney Water works on a main nearby, your taps may splutter or run discoloured for a while afterwards. Grit can lodge in aerators and mixer cartridges, making them drip or lose flow. Rinse the aerators first. If a mixer starts dripping straight after mains work, the cartridge may just need cleaning.

Ensuite and basin mixers

Ensuites in the newer Little Bay homes often have small basin mixers in a vanity with little room underneath. Leaks from the flexible hoses or the mixer base soak the vanity before anyone notices. If the bottom of the vanity is swollen or stained, look underneath for drips. Replacing the hoses and the base seal usually fixes it if caught early, and it saves the vanity from needing replacement.

While we're there, we check that the isolating valves under the vanity turn freely, so the basin can be turned off on its own next time.

What happens when you call

1

Tell us what's going on

Call or send a quick form. A photo of the problem helps us come prepared. No call-out fee.

2

Options and a fixed price first

We find the cause, explain your options and give you a fixed price for each before any work starts.

3

Fixed, tested and backed

We do the work, test it, clean up, and back our workmanship with a lifetime labour warranty.

Jobs we finished recently

Toilet before repair in Chifley
Toilet before repair in Chifley
Toilet after repair in Chifley
Toilet after repair in Chifley

See more recent projects

Why Little Bay homeowners call us

  • Based in Matraville, just up the road from Little Bay
  • Rated 5.0 from 110 Google reviews
  • Free quotes, with options and a fixed price before any work starts
  • Lifetime labour warranty on our workmanship
  • Licensed plumbers, drainers and gasfitters (Lic. 398171C)

Tap repair questions from Little Bay homeowners

Why do my outdoor taps keep seizing?

Sea air corrodes the brass and spindle. Regular use and a coastal-suited replacement help.

My outdoor shower drips. Can you fix it?

Yes. Usually a new cartridge; if the body is corroded, a new mixer.

Why does my washer tap still drip with a new washer?

The seat is worn. We re-cut it.

Can you repair my mixer?

Usually, with a new cartridge.

Can you convert washer taps to quarter-turn?

Often, with ceramic disc spindles.

My garden tap snapped. What now?

Turn the water off at the meter and call us.

Why is the flow weak?

Often sand in the aerator or rose. Rinse it out.

Do I need to turn all the water off?

Only without an isolating valve. We can fit them.

Can you replace my washing machine taps?

Yes, with quarter-turn valves and new hoses.

Can you supply the tap?

Yes, or fit one you've bought.

How long does a repair take?

Most take under an hour.

Can you fix several taps in one visit?

Yes.

More plumbing in Little Bay: our Little Bay plumber page, taps and toilets, toilet repairs, leak detection, burst pipes and hot water. Nearby: tap repairs in Malabar and Matraville. Guides: mixer tap leaking, ceramic disc vs washer taps and dripping taps guide.

Call 0401 758 373Free quote