★★★★★ 5.0 from 100+ Google reviews · Your Sydney Plumber

Tap repairs in La Perouse 2036

We repair and replace taps in La Perouse homes: dripping washer taps, leaking kitchen and basin mixers, shower taps, laundry taps, seized and corroded garden taps and risers, and outdoor shower mixers. We re-cut worn tap seats, replace cartridges, O-rings and spindles, and fit new taps suited to coastal conditions when a repair won't last. You get options and a fixed price before any work starts, backed by our lifetime labour warranty.

On the La Perouse headland, taps have two enemies: everyday wear inside the home, and salt air outside it. Washer taps drip as their seats wear, mixers stiffen as their cartridges age, and garden taps and outdoor showers corrode and seize in the sea air. A dripping tap wastes water every minute, and a seized outdoor tap can snap off its pipe when you try to force it. We're a short drive away in Matraville, and most tap repairs are done in one visit.

Tap repairs we do

Dripping washer taps

New washers and re-cut seats so the tap shuts off cleanly.

Leaking mixers

Cartridges, O-rings and seals replaced, or the mixer replaced.

Seized garden taps

Corroded taps and risers replaced with fittings suited to salt air.

Outdoor shower mixers

Mixers and taps repaired or replaced, and roses cleaned or swapped.

Shower and basin taps

Spindles and cartridges replaced from the front, usually without removing tiles.

Laundry taps

Stiff, dripping or corroded laundry taps repaired or replaced.

Signs a tap needs repair

  • Drips from the spout after it's turned off.
  • Water at the handle or around the base.
  • Hard to turn, or seized solid.
  • Green crust, rust or white salt on the tap body.
  • Wobbles on its pipe when you turn it.
  • Squeals or shudders when turned on.
  • Low flow or a spluttering stream.
  • Sand or grit coming out with the water.

Why taps fail in La Perouse homes

Salt air outside

Outdoor taps sit in salty air every day. The spindle seizes in the body, the brass corrodes, and the pipe feeding the tap rusts or thins where it leaves the ground. Taps facing the water wear out fastest.

Washer taps

Traditional washer taps close by pressing a rubber washer onto a brass seat. Over the years, the washer hardens and the seat wears a groove. A new washer on a worn seat drips again soon, which is why we re-cut the seat as part of the repair.

Mixer cartridges

Mixers use a cartridge to control flow and temperature. After 10 to 20 years, the cartridge wears or its seals perish, and the mixer drips or stiffens.

Sand and grit

Beach sand gets into outdoor shower mixers and roses, and grit from older pipes wears washers and cartridges faster.

Water pressure

High pressure wears washers and cartridges faster and can make taps bang when they shut. A pressure limiting valve protects every tap.

La Perouse homes and their taps

WhereTypical tapsCommon faults
Garden and outside wallsBrass garden taps on copper or steel risersSeized spindles, corroded bodies, rusted risers
Outdoor showersMixers or two-tap setsSand in the mixer, corrosion, drips
Bathroom and laundryWasher taps or mixersWorn seats, stiff spindles, drips
KitchenMixersWorn cartridges, leaking bases

How we repair a tap

  1. Ask what's happening, and for a photo and any brand name.
  2. Turn off the water at the isolating valve or meter.
  3. Take the tap apart and find the worn or corroded part.
  4. Give you options: repair, convert or replace, each with a fixed price.
  5. Repair it properly: re-cut seats, new washers, O-rings, spindles or cartridges.
  6. Test it for drips, leaks and smooth operation.

Repair, convert or replace?

SituationUsually best
Washer tap with a sound bodyRepair with a new washer and re-cut seat
Seized or corroded outdoor tapReplace the tap, and the riser if it's corroded
Washer taps you'd like easier to useConvert to quarter-turn ceramic spindles
Mixer dripping, cartridge availableNew cartridge
Mixer with no parts availableReplace the mixer

What affects the cost

  • The type of tap and whether parts are available.
  • Corrosion: seized fittings take longer to remove.
  • How many taps are done in one visit.
  • Access: shower taps behind tiles, tight vanities.
  • New tapware: depends on the model.

You get a fixed price before any work starts.

Who's responsible?

  • You: taps, mixers and isolating valves on your property.
  • Sydney Water: the supply up to the meter.

Signs it's urgent and when it can wait

  • Call straight away if a tap won't turn off, or an outdoor tap has snapped off and is spraying.
  • Call soon if a shower tap leaks behind the tiles or a tap leaks at the base into the cupboard.
  • Book a time if a tap drips, is stiff or is showing corrosion.

A recent tap repair nearby

Here's a recent tap repair nearby in Maroubra, done on the same visit as a drain clear.

Leaking taps fixed during a drain clear, Maroubra (nearby)

The problem: a Maroubra home had leaking taps as well as slow drains.

What we did: we laid a mat to protect the floor, jetted the drains and floor wastes clear, and then repaired the leaking taps on the same visit.

The result: the taps shut off properly and the drains flow freely, all in one visit.

Floor protected during tap repairs near La Perouse
Floor protected, Maroubra
Drain jetting on the same visit as tap repairs near La Perouse
Drains cleared on the same visit

“Great plumber, fixed my leaking taps quickly and at a great price!”

Tom (Google review)

More local work is on our recent projects page.

Tap repairs across La Perouse

  • Around Yarra Road, Elaroo Avenue and Wybalena Avenue: older washer taps inside and out.
  • Around Adina Avenue, Canara Avenue and Coonda Avenue: a mix of washer taps and mixers.
  • Near The Loop and Anzac Parade: garden taps most exposed to salt air.
  • Towards Frenchmans Bay and Congwong Bay: outdoor showers by the beaches.
  • Towards Phillip Bay and Little Bay: slightly more sheltered streets.

Garden taps by the sea

A garden tap that's stiff, seized or wobbly is telling you something. Don't force a seized outdoor tap: the riser below it may be corroded at ground level and can snap, leaving water spraying until you get to the meter. We replace the tap and the riser together, using fittings that stand up better to salt air, and fix them securely to the wall or a post. If you use the garden tap often, a quarter-turn hose cock is easier to use and less likely to seize.

Outdoor shower mixers

Outdoor showers take sand, salt and sun every day. Sand gets into the mixer cartridge and wears it, salt corrodes the body and fittings, and the rose clogs. We clean or replace roses, repair or replace mixers and taps, and can fit a mixer that's easier to maintain in coastal conditions. Rinsing the rose and running the mixer through hot and cold after each use helps it last.

Kitchen and basin mixers

A kitchen mixer that drips or stiffens usually needs a new cartridge. Water around the base often runs into the cupboard below, so check inside if you see damp. We identify the brand and model, replace the cartridge or the mixer, and check the hoses and isolating valves while we're there. If you'd like filtered water, a filtered mixer can go in the same hole. See water filters in La Perouse.

Shower taps

Shower taps can cause hidden damage. If a spindle seal fails, water can leak into the wall every time the shower runs. Signs include damp skirting boards on the other side of the wall, loose tiles, mould along the grout or a musty smell. Most repairs are done from the front without removing tiles. See leak detection in La Perouse if you suspect a hidden leak.

Laundry taps

Laundry taps are often left open for years to supply the washing machine, and in damp coastal laundries they stiffen and corrode. The machine hoses can corrode and burst too. A single-lever machine tap that turns hot and cold off together makes it easy to shut off the machine when you go away.

Washer taps: repair them properly

The most common reason a washer tap keeps dripping is that only the washer gets changed. A proper repair re-cuts the seat so it's smooth and flat again, fits a new washer, and replaces the spindle O-rings while the tap is open. Done properly, a washer tap repair lasts for years.

Converting to quarter-turn

Ceramic disc conversion spindles turn traditional washer taps into quarter-turn taps without changing the tap bodies. They shut off with a light touch and drip far less.

Choosing new tapware for a coastal home

  • Outdoor taps: choose quality brass or fittings designed for coastal use, and fix them firmly.
  • Outdoor showers: pick a mixer and rose that are easy to clean and service.
  • Indoor taps: match the holes, choose solid brass, and pick a brand with local parts.
  • Finishes: some finishes stand up to salty air better than others; ask us before you buy.
  • Ease of use: lever handles are easier for children and older hands.

Low flow at a tap

If one tap has low flow while others are fine, the cause is usually at that tap: a blocked aerator, sand in the mixer, a partly closed isolating valve or a worn cartridge. Unscrewing and rinsing the aerator often fixes it. If every tap has low flow, the cause is further back: the meter valve, a pressure problem, or old galvanised pipes narrowing inside.

Dripping taps and your water bill

A single dripping tap runs every minute of every day. Over a year, a steady drip can add up to thousands of litres. A dripping hot tap also wastes the energy used to heat the water. A dripping outdoor tap can go unnoticed for months, because the water soaks into the sand.

Taps that bang or shudder

If a pipe bangs when you turn a tap off quickly, that's water hammer. It's most common with quarter-turn taps, mixers and washing machine valves that close fast. A tap that shudders while running usually has a loose washer or worn spindle. See water hammer.

Hot taps that run cold, or cold taps that run warm

If a mixer gives warm water when set to cold, a worn cartridge may be letting hot and cold cross over. If the hot takes a long time or runs out, the problem may be at the hot water system. See hot water in La Perouse.

Isolating valves under the sink

Isolating valves let you turn off one tap without shutting off the whole home. In coastal homes, they stiffen and seize faster. When a tap needs repair and the valve won't turn, the water has to go off at the meter. We replace seized valves as part of a tap repair.

Getting ready for our visit

  • Take a photo of the tap and any brand name on it.
  • Clear the cupboard under the sink or vanity.
  • Know where your meter is.
  • Tell us about access: gates, dogs, stairs and parking.
  • List every tap you'd like looked at, inside and out.

Looking after your taps

  • Turn outdoor taps on and off every few weeks so they don't seize.
  • Rinse salt off outdoor taps with fresh water occasionally.
  • Don't over-tighten washer taps.
  • Rinse aerators and shower roses to clear sand.
  • Turn isolating valves off and on once a year.
  • Fix drips early, before they wear the seat badly.

What to expect on the day

We give you a time window and let you know when we're on the way. Most tap repairs are done in one visit with parts from the van. We protect your floor, turn off the water, take the tap apart and show you the worn or corroded parts. Once it's repaired, we test it and make sure it turns smoothly.

Hose cocks and garden hoses

A hose cock left on with the garden hose attached holds the hose under pressure all day. In the sun and salt air, the hose connector can corrode onto the tap thread, and the hose can split. Turn the hose cock off when you've finished, and replace a corroded connector before it seizes on. If the hose cock itself drips or won't turn, we can replace it.

Taps in homes that sit quiet

Taps that aren't used for weeks, in a holiday home or a spare bathroom, can stiffen, and their washers and O-rings can dry out. Outdoor taps that sit unused are the most likely to seize. When you arrive, turn each tap on and off, and run each one for a moment. If a tap is stiff, don't force it; let us know.

Taps for every age

Stiff washer taps are hard for small hands and sore fingers. Lever mixers and quarter-turn taps need only a light push. Pairing new bathroom taps with a tempering valve on the hot water reduces the risk of scalds. See tempering valve installation.

Why our tap repairs last

We repair taps the way they should be repaired: re-cut seats instead of just swapping washers, quality washers and O-rings, cartridges that match the original, and outdoor fittings chosen for coastal conditions. We test every tap before we leave. Our labour is covered by a lifetime warranty.

Why La Perouse homeowners call us

We're a short drive away in Matraville and repair taps across La Perouse, Little Bay, Chifley and Phillip Bay, from dripping washer taps to seized garden taps and outdoor showers. You get options and a fixed price before any work starts. If something is dripping or seized, send us a photo and we'll tell you the likely fix before we arrive.

Summer and outdoor taps

Outdoor taps and showers get their heaviest use over summer, when sandy feet, wetsuits and dive gear all need rinsing. If an outdoor tap has been stiff or dripping, get it fixed in spring. A snapped riser on a busy summer weekend means the water off at the meter until it's repaired.

Corrosion you can see on taps

  • Green or blue crust on brass or copper: surface corrosion, worth watching.
  • White salt deposits: salt building up, which holds moisture against the metal.
  • Pink or pale patches on brass: a sign the brass is breaking down (dezincification), which weakens the tap.
  • Orange rust on a steel riser or bracket: the steel is failing.
  • A tap that moves when you turn it: the riser or fixing has corroded.

Send us a photo of anything that worries you and we'll tell you whether it needs attention now or can wait.

Pull-out and spray mixers

Pull-out kitchen mixers have a flexible hose that runs down through the mixer and loops under the sink. Over time, the hose can crack or wear where it rubs, and water drips into the cupboard when the tap runs. We can usually replace the hose or spray head on its own if parts are available, or replace the mixer if they're not.

Wall-mounted shower and bath mixers

Wall-mounted mixers sit on a body inside the wall, with the cartridge accessed from the front. When they drip or stiffen, a new cartridge usually fixes it. If the body itself is leaking inside the wall, we'll explain the options before anything is opened.

A tap check before summer

Spring is a good time to walk around the home and try every tap, inside and out. Look for drips, stiffness, wobbles and corrosion. Rinse aerators and shower roses. If anything needs attention, book it in before the house fills up for the holidays.

Repairing old taps you love

Some La Perouse homes have older tapware with character that owners want to keep. Most traditional taps can be repaired: new washers, re-cut seats, new O-rings and, where needed, new spindles that fit the original bodies. If the original spindle is worn beyond repair, ceramic disc conversion spindles often fit, keeping the look while improving how the tap works. We'll tell you honestly what can be saved and what can't, and give you a fixed price for each option.

Sand in mixers and roses

Beach sand is gritty and hard. When it gets into a mixer cartridge, it scratches the ceramic discs and causes drips. When it gets into a shower rose, it blocks the holes and gives a weak, uneven spray. Rinsing off before using an indoor shower, and running outdoor shower mixers through full hot and cold after use, helps flush sand out. If a mixer has started dripping after a summer of sandy use, a new cartridge usually fixes it.

However old or new your taps are, the aim is the same: taps that turn easily, shut off cleanly and last.

Tap words explained

  • Washer: the rubber disc that seals a traditional tap.
  • Seat: the brass ring inside the tap body that the washer closes on.
  • Spindle: the part that turns when you turn the handle.
  • Riser: the pipe rising from the ground to an outdoor tap.
  • Cartridge: the unit inside a mixer or quarter-turn tap.
  • Aerator: the screen at the end of the spout.
  • Isolating valve: a small valve that turns off water to one tap.

What happens when you call

1

Tell us what's going on

Call or send a quick form. A photo of the problem helps us come prepared. No call-out fee.

2

Options and a fixed price first

We find the cause, explain your options and give you a fixed price for each before any work starts.

3

Fixed, tested and backed

We do the work, test it, clean up, and back our workmanship with a lifetime labour warranty.

Jobs we finished recently

Toilet before repair in Chifley
Toilet before repair in Chifley
Toilet after repair in Chifley
Toilet after repair in Chifley

See more recent projects

Why La Perouse homeowners call us

  • Based in Matraville, a short drive from La Perouse
  • Rated 5.0 from 110 Google reviews
  • Free quotes, with options and a fixed price before any work starts
  • Lifetime labour warranty on our workmanship
  • Licensed plumbers, drainers and gasfitters (Lic. 398171C)

Tap repair questions from La Perouse homeowners

Why do my garden taps seize?

Salt air corrodes the spindle and body. Turning them regularly helps.

My garden tap wobbles. Should I worry?

Yes. The riser may be corroded and close to snapping.

Can you fix my outdoor shower?

Yes, the mixer, taps and rose.

Why does my tap still drip after a new washer?

The seat is usually worn. We re-cut it.

Can you fix a dripping mixer?

Usually, with a new cartridge.

Can you repair a shower tap without removing tiles?

In most cases, yes, from the front.

Can washer taps be converted to quarter-turn?

Often, with ceramic disc spindles.

Do I need to turn off all the water?

Only without a working isolating valve. We can fit one.

Can you supply new taps?

Yes, including ones suited to coastal conditions.

How long does a tap repair take?

Most take under an hour.

Can you do several taps in one visit?

Yes, inside and out.

What warranty do I get?

Our workmanship carries a lifetime labour warranty.

More plumbing in La Perouse: our La Perouse plumber page, taps and toilets, toilet repair and water filters. Nearby: tap repair in Little Bay, Chifley and Malabar. Guides: mixer tap leaking and ceramic disc vs washer taps.

Call 0401 758 373Free quote