Tap repairs in Maroubra 2035
A dripping tap wastes water every minute of the day, stains basins and gets worse over time. A tap leaking inside the wall can quietly damage tiles, plaster and timber. We're based next door in Matraville and repair taps for homeowners across Maroubra, from the beach streets to Maroubra Junction, Coral Sea Park and South Maroubra.
Tap problems we fix in Maroubra
Dripping from the spout
On an older-style tap with separate hot and cold handles, a drip from the spout usually means a worn washer or a worn seat (the brass surface the washer closes on). On a mixer tap, it usually means the cartridge inside has worn out. Both are repairable in most cases.
Leaking around the handle or the base
Water coming out around the handle, or pooling at the base of a mixer, usually means worn O-rings or a failing cartridge. If water is getting under the basin or into the cabinet, it's worth fixing quickly before it swells the timber. See mixer tap leaking at the base.
Stiff, loose or noisy taps
Taps that are hard to turn, spin without stopping, or shudder and bang when you turn them on usually have worn internal parts or loose jumper valves. Noisy taps can also be a sign of high water pressure.
Low flow from one tap
If one tap is weak but the others are fine, the aerator (the screen on the end of the spout) may be blocked with grit, or the cartridge or washer may be failing. If every tap is weak, the problem is more likely in the pipes. See our water pressure guide.
Taps leaking inside the wall
Shower and bath taps are set into the wall, and the tap body or the pipe behind it can leak where you can't see it. Signs include loose or drummy tiles, mould at the bottom of the wall, damp in the next room, or a wet patch on the ceiling below an upstairs bathroom. See bath leaking through the ceiling.
Garden and outdoor taps
Outdoor taps get knocked, left half-on and baked in the sun. In Maroubra's beach streets, salt air corrodes brass and chrome quickly, so outdoor taps seize, crack or drip. A dripping garden tap is easy to ignore, but it adds up on the water bill.
Taps in different kinds of Maroubra homes
Older homes with washer taps
Many interwar and post-war homes around Maroubra Junction, Coral Sea Park and South Maroubra still have traditional washer taps (also called jumper valve taps), especially in laundries and bathrooms that haven't been updated. These are easy to repair and parts are cheap, but the brass seats inside can wear. We can re-seat them or fit ceramic disc spindles, which turn a quarter-turn and last longer. See ceramic disc vs washer taps.
Newer kitchens and bathrooms with mixers
Updated kitchens and bathrooms, newer townhouses and units mostly have mixer taps. Mixers use a cartridge, and there are hundreds of different cartridges. We identify the brand and model, and either fit a matching cartridge or advise you if it's cheaper and longer-lasting to replace the mixer.
Homes near the beach
Close to Maroubra Beach, the salt air attacks outdoor taps, hose connectors, shower roses and the chrome on fittings near open windows. Outdoor taps often seize in the open position or snap at the thread. We use quality brass fittings outside so the repair lasts.
Units and walk-up flats
In units, a leaking tap can affect the neighbours below, so it's worth fixing early. Taps and pipes inside your own unit are something we can repair for you directly.
Laundry and washing machine taps
Laundry taps in older Maroubra homes are often the oldest taps in the house, sometimes original to the home, and the washing machine stop taps behind the machine are rarely turned. When they're finally needed, they leak or won't shut off. Washing machine hoses also wear out and can burst. We replace old laundry taps and machine stop taps with quarter-turn valves that are easy to shut off, and fit new hoses if the old ones are bulging or rusted.
Hot water taps that drip or run cold
Hot taps wear faster than cold ones because heat hardens washers and seals. A dripping hot tap also wastes the energy used to heat the water. If the hot tap runs lukewarm, takes ages to get hot, or the water is too hot, the problem may be the hot water system or the tempering valve rather than the tap. See hot water in Maroubra and our hot water temperature guide.
Taps, water hammer and high pressure
If your taps bang or shudder when you turn them off, or washers keep wearing out quickly, the water pressure in your home may be too high. Pressure varies across Maroubra with the height of the street. A pressure limiting valve at the meter protects every tap, hose and appliance in the house, and makes washers and cartridges last longer. See pressure limiting valves.
Kitchen taps and water filters
If you're replacing a kitchen mixer, it's a good time to think about filtered water. A filter under the sink with its own small tap, or a mixer with a built-in filter outlet, gives you better-tasting drinking water without buying bottled water. See water filters in Maroubra.
Tap repairs across Maroubra, area by area
- North Maroubra and the beach streets: salt air is hardest on outdoor taps, hose connectors and shower fittings near open windows. We use quality brass outside.
- Maroubra Junction and the streets off Maroubra Road: older semis and bungalows with original washer taps in laundries and bathrooms, often without isolating valves.
- Coral Sea Park and South Maroubra: post-war homes with bathrooms updated in the 1980s and 1990s, where early mixers and ceramic disc taps are now wearing out.
- Walk-up flats and newer units: mixer taps and wall shower mixers, where a slow leak can reach the unit below.
How we repair taps in Maroubra
- Turn the water off at the isolating valve under the sink, or at the main stop tap if there isn't one.
- Take the tap apart and find the cause: washer, seat, O-ring, jumper valve, cartridge or the tap body itself.
- Give you options. Repair the tap, or replace it if it's worn out, cracked or parts aren't available. You get a fixed price for each before we start.
- Repair or replace with quality parts, re-seat worn brass seats where needed, and clean the aerator.
- Test for drips, leaks and flow, and check the isolating valves and flexi hoses while we're there.
Washer taps
New washers, jumper valves and O-rings, and worn seats re-cut so the tap shuts off properly.
Mixer taps
Cartridges replaced with the right part for your brand, or the mixer replaced if that's better value.
Shower and bath taps
Wall taps repaired or upgraded, and leaks behind the tiles found and fixed.
Outdoor taps
Seized, cracked and dripping garden taps replaced with quality brass taps.
Isolating valves and hoses
Under-sink stop valves and flexible hoses replaced so the tap can be turned off on its own.
New taps fitted
Kitchen, basin, laundry and outdoor taps supplied and installed.
Repair or replace your tap?
| Problem | Usually a repair | Usually a replacement |
|---|---|---|
| Washer tap dripping | New washer and re-seat the tap | Tap body is cracked or badly corroded |
| Mixer dripping | New cartridge | Cartridge not available, or the mixer is old and cheap |
| Leaking at the handle | New O-rings or cartridge | Handle or body is broken |
| Outdoor tap seized | Free it up and service it | Corroded tap, or it snaps at the thread |
| Shower tap leaking in the wall | Repair the tap body or connection | Upgrade to a new mixer if the old body is failing |
What affects the cost of a tap repair
- The type of tap. Washer taps are usually quick. Mixers depend on the cartridge and whether it's in stock.
- How many taps. If several taps are dripping, fixing them in one visit saves you a second call-out.
- Access. Taps under tight cabinets, or wall taps behind tiles, take longer.
- Parts. Some imported mixers need parts ordered in.
- Replacement. A new tap depends on the model you choose.
You'll have a fixed price before any work starts.
Who's responsible?
- You (the homeowner) look after all the taps and pipes on the house side of the water meter.
- Sydney Water looks after the water meter and the main in the street.
- In units, taps inside your unit are usually yours, and shared pipes are usually the building's.
Quick checks you can do
- Spout drip or handle leak? Dry the tap with a towel and watch it for a minute. Drips from the spout point to a washer or cartridge; water around the handle points to an O-ring or cartridge.
- Weak flow? Unscrew the aerator at the end of the spout and rinse out any grit.
- Can you isolate it? Look under the sink or basin for small stop valves. If they won't turn, they're worth replacing.
- Leak in the wall? Turn the shower taps off hard and check the floor and wall outside the shower over the next day. Damp that appears without the shower running points to a leak in the wall.
Our dripping taps guide has more tips.
Tap repair step by step: what we actually do
People often ask what's involved in fixing a tap. For a typical dripping washer tap in a Maroubra bathroom, the job goes like this:
- Isolate the water. We turn off the isolating valve under the basin. Many older Maroubra bathrooms don't have one, so we turn the water off at the meter and let you know before we do.
- Protect the basin. We put a towel in the basin and over the plug hole so small parts can't be dropped down the drain or chip the porcelain.
- Remove the handle and cover. Older handles can be stuck on with years of scale, so we free them carefully to avoid cracking the chrome.
- Take out the spindle (jumper valve). We check the washer, the jumper, the O-rings and the thread on the spindle for wear.
- Check the seat. If the brass seat inside the tap body is pitted or grooved, a new washer won't seal for long. We re-cut the seat with a seat cutter so it's smooth again.
- Fit new parts. New washer, jumper and O-rings, or a ceramic disc spindle if you'd like a quarter-turn tap.
- Reassemble and test. We turn the water back on, open and close the tap several times, and watch for drips at the spout and around the handle.
A mixer tap is similar, except the whole cartridge is replaced as one part. The tricky bit is finding the right cartridge: we check the brand, model and the spline count on the stem before ordering.
Tap types you'll find in Maroubra homes
| Tap type | Where you'll see it | Common faults | Usual fix |
|---|---|---|---|
| Washer (jumper valve) taps | Older bathrooms and laundries, outdoor taps | Spout drips, stiff handles, worn seats | New washer and jumper, re-cut seat |
| Ceramic disc taps | 1990s and later bathrooms | Dripping when the disc is chipped or dirty | New ceramic disc spindle |
| Single-lever mixers | Kitchens, newer bathrooms and units | Drips, leaks at the base, stiff lever | New cartridge or new mixer |
| Wall shower mixers | Showers and baths | Drips at the rose, leaks behind tiles | New cartridge, repair the body or replace |
| Hose taps and garden taps | Front and back yards, side passages | Seized, cracked, dripping | Service or replace with quality brass |
| Washing machine stop taps | Laundries | Won't shut off, leaks at the spindle | Replace with quarter-turn valves |
Signs a tap problem is urgent and when it can wait
- Call us soon if water is leaking inside a wall or under a floor, a tap won't turn off at all, a tap body has cracked, or water is leaking into a cabinet or onto a timber floor.
- Book a time if a tap drips slowly from the spout, a handle is stiff, or an outdoor tap drips. These are worth fixing soon to save water, but they won't cause damage overnight.
- Mention it next time we're there if a tap is a little noisy or an aerator is spraying sideways. We can usually sort these in a few minutes while we're on site for another job.
A tap maintenance checklist for your home
A few minutes a year keeps taps working and stops small leaks turning into big ones:
- Unscrew and rinse the aerators on kitchen and basin taps every few months.
- Turn every isolating valve under sinks and basins off and on again once a year so they don't seize.
- Turn the washing machine stop taps a few times a year.
- Check outdoor taps after summer for drips and cracked hose fittings, especially near the beach.
- Look under sinks for damp, swelling or water marks in the cabinet base.
- Don't over-tighten washer taps to stop a drip. It wears the washer and seat faster.
Plumbing words explained
- Washer: the rubber disc at the bottom of the spindle that presses on the seat to stop the water.
- Jumper valve: the small part the washer sits on, inside a traditional tap.
- Seat: the brass ring inside the tap body that the washer closes against. If it's worn, the tap keeps dripping even with a new washer.
- Spindle: the threaded stem the handle turns.
- Cartridge: the sealed unit inside a mixer tap that controls the flow and mixes hot and cold.
- Aerator: the screen on the end of the spout that mixes air into the water and catches grit.
- Isolating valve: a small stop tap under a sink or basin that turns off the water to that tap only.
What our customers say
“Great plumber, fixed my leaking taps quickly and at a great price!”
Tom (Google review)
Our recent tap repairs in Maroubra
Blocked drains cleared and leaking taps fixed in one visit, Maroubra
The problem: a Maroubra home had slow, blocked drains and leaking tapware.
What we did: we laid down a protective mat to keep the floor clean, cleared the drains and floor wastes with high-pressure jetting, then repaired the leaking taps in the same visit.
The result: the drains flow freely and the taps shut off properly, without the owners needing a second call-out.


More local jobs are on our recent projects page.
Choosing a new tap
If you're replacing a tap, these points help it last and fit:
- Check the holes. Basins and sinks come with one, two or three tap holes. A new tap needs to suit the holes you have, or the sink needs replacing too.
- Choose quality brass. Cheap taps with plastic or zinc bodies don't last, especially outdoors near the beach.
- Look for a good WELS rating to save water.
- Think about spare parts. Well-known brands are easier to repair in ten years' time.
- Ask about a mixer. In a kitchen or laundry, a single-lever mixer is easy to use and to turn off fully.
Why fix a dripping tap now
A tap dripping once a second wastes a surprising amount of water over a year, and a hot tap drip also wastes the energy used to heat it. Drips also leave stains and scale on basins, and a tap that's left dripping usually gets worse as the washer or cartridge wears further. In units, a leak can reach the neighbours below. Fixing it early is almost always the cheapest option.
What to expect on the day
We give you a time window and let you know when we're on the way. Most tap repairs are done in one visit with the parts on the van. If your mixer needs a special cartridge, we'll identify it, order it and come back to fit it. We protect benchtops and floors, and clean up before we leave. If other taps in the house are showing early signs of wear, we'll point them out so you can decide whether to fix them at the same time.
What happens when you call
Tell us what's going on
Call or send a quick form. A photo of the problem helps us come prepared. No call-out fee.
Options and a fixed price first
We find the cause, explain your options and give you a fixed price for each before any work starts.
Fixed, tested and backed
We do the work, test it, clean up, and back our workmanship with a lifetime labour warranty.
Jobs we finished recently


Why Maroubra homeowners call us
- Based in Matraville, a few minutes from every street in Maroubra
- Rated 5.0 from 110 Google reviews
- Free quotes, with options and a fixed price before any work starts
- Lifetime labour warranty on our workmanship
- Licensed plumbers, drainers and gasfitters (Lic. 398171C)
Tap repair questions from Maroubra homeowners
Why does my tap keep dripping after I turn it off hard?
On a washer tap, the washer or the seat is worn, so turning it harder only crushes the washer further. A new washer and a re-cut seat usually fixes it.
Can you repair a mixer tap or does it need replacing?
Most mixers can be repaired with a new cartridge if we can get the right one. If the cartridge isn't available or the mixer is old, a new mixer can be better value.
Why is water coming out from under my mixer?
Usually worn O-rings or a failing cartridge. It should be fixed quickly so water doesn't damage the cabinet or benchtop.
My shower tap is leaking behind the tiles. What can you do?
We find where the leak is, then repair or replace the tap body or connection. We keep tile removal to a minimum.
How long does a tap repair take?
Most tap repairs take less than an hour. Replacing a tap or fixing a wall tap can take longer.
Why do my outdoor taps keep seizing?
Salt air, sun and mineral build-up are hard on outdoor taps, especially near the beach. A quality brass tap and regular use help.
Should I change washer taps to ceramic disc?
Ceramic disc spindles turn a quarter-turn, are easy to use and last longer. We can fit them to many existing taps.
Can you fix several taps in one visit?
Yes. If a few taps are dripping, fixing them together saves you a second call-out.
Do I need to turn the water off to the whole house?
Only if the tap has no isolating valve under it. Many older Maroubra homes don't, so we turn it off at the meter for a short time and can fit isolating valves while we're there.
Can you supply the new tap?
Yes. We can supply quality taps, or fit one you've bought. If you're buying your own, send us a photo or the model first so we can check it suits your sink or basin.
More plumbing in Maroubra: our Maroubra plumber page, taps and toilets, toilet repair, burst pipes, leak detection and water filters. Nearby: taps in Matraville and taps in Malabar. Related: mixer tap leaking and ceramic disc vs washer taps.