Burst pipe repairs in Maroubra 2035
A burst pipe can do a lot of damage in a short time: water through the ceiling, a flooded laundry, a soggy yard or a water bill that suddenly doubles. We're based next door in Matraville and repair burst and leaking water pipes for homes right across Maroubra, from North Maroubra and the beach streets to Maroubra Junction and South Maroubra.
First, turn the water off
If water is pouring out of a pipe in your Maroubra home, the most important thing is to stop it. Here's how:
- Find the main stop tap. In most Maroubra houses it's at the water meter, near the front boundary or in the front garden. In semis it's usually beside the meter at the front, and in townhouses and units it may be in a meter box or cupboard.
- Turn it clockwise until it stops. Older taps can be stiff. Use a cloth for grip, but don't force it so hard that it breaks.
- Turn off the hot water system if the burst is on a hot pipe. Switch off the power to an electric unit, or turn a gas unit to pilot or off.
- Turn off the power at the switchboard if water is near power points, lights or appliances.
- Move valuables and soak up what you can with towels, and put a bucket under drips from the ceiling.
Our water shut-off guide shows where to look and what the different taps look like. Once the water is off, give us a call.
Signs of a burst or leaking pipe in a Maroubra home
Not every burst pipe sprays water across the room. Many leak quietly inside a wall, under the floor or under the yard. Watch for these signs:
- Water you can see: a wet patch on a ceiling or wall, water under the sink, or a puddle that keeps coming back.
- A wet patch in the yard that stays green or soggy in dry weather, often along the line from the meter to the house. See our wet patch in the yard page.
- Low water pressure all of a sudden, at every tap.
- The sound of running water when every tap is off. Our hear water running page explains what it can mean.
- A water meter that keeps ticking with everything turned off.
- A higher water bill with no change in how you use water.
- Bubbling paint, swelling skirting boards or mould on a wall where a pipe runs. See mould on walls.
- Rusty or discoloured water from old galvanised pipes that are rusting from the inside.
Why pipes burst in Maroubra homes
Sydney doesn't get the freezing weather that bursts pipes in colder places, so when a pipe fails here there's usually another cause. These are the ones we see most in Maroubra.
Old galvanised steel pipes
Many Maroubra houses built from the 1920s to the 1950s were plumbed with galvanised steel water pipe. It rusts from the inside out. The pipe narrows, the pressure drops, and eventually the thinnest point splits, usually at a thread or joint. If your home still has galvanised pipe, one burst is often followed by another. Our galvanised pipes guide explains how to tell and what the options are.
Ageing copper
Copper replaced galvanised from the 1950s onwards and lasts well, but after 50 or 60 years it can develop pinholes, especially at bends and where it's clipped against brick or concrete. In the streets near the beach, copper and brass fittings outside the house also corrode faster in the salt air. Green crust on copper fittings is an early warning. See green copper pipes.
Water pressure
Mains pressure varies across Maroubra depending on the height of the street and the water supply network. High pressure strains pipes, fittings, flexible hoses and hot water valves, and makes water hammer (the bang when a tap shuts off) worse. A pressure limiting valve at the meter protects the whole house. See our pressure limiting valve page.
Failed flexible hoses
The braided flexible hoses under sinks, basins and toilets are one of the most common causes of a sudden indoor flood. They have a limited life, and a hose that's kinked, rusty or bulging can let go without warning. See flexi hose replacement.
Shifting sand and tree roots
The water service from the meter to the house runs through Maroubra's sandy soil. Sand moves as it wets and dries, and big tree roots push against pipes as they grow. Over time that movement cracks old pipes and pulls joints apart, which is why so many leaks we find in Maroubra are underground between the meter and the house.
Accidents during other work
Nails, screws and drills through walls, digging in the garden, and new fence posts are all common causes of a pipe being hit. If you're putting up shelves or a new fence, it's worth knowing where your pipes run.
Burst pipes in different kinds of Maroubra homes
Interwar bungalows and semis
Older homes around Maroubra Junction and the streets off Maroubra Road often have a mix of original galvanised pipe and later copper repairs, sometimes running under timber floors. Getting under the floor is usually possible, which makes repairs easier than in a slab home. In semis, the water service sometimes runs past the neighbour's half, so we check where the line goes before we dig.
Post-war brick and fibro homes
In South Maroubra and Coral Sea Park, many 1950s and 1960s homes have copper pipe that is now reaching the end of its life, and some still have galvanised sections near the meter. Leaks often show up first as a wet patch in the front yard.
Walk-up flats and units
Maroubra has plenty of 1960s and 1970s walk-up unit blocks near the beach and Maroubra Junction. A burst pipe inside your own unit (under the sink, behind the basin, or in your bathroom wall) is something we can fix for you directly. Pipes in the common areas or shared risers are usually the building's responsibility.
Newer homes on slabs
Newer townhouses and rebuilt homes often have water pipes in or under the concrete slab. A leak under a slab is harder to find, which is where our leak detection equipment saves a lot of digging. See leak detection in Maroubra.
Burst pipes across Maroubra, area by area
- Maroubra Junction and the older streets: galvanised pipe in interwar homes, often under timber floors, where one burst is often followed by another.
- North Maroubra and the beach streets: salt air on outdoor copper and brass, and water services running through deep sand.
- Coral Sea Park and South Maroubra: 1950s and 1960s copper reaching the end of its life, with leaks often showing as a wet patch in the front yard.
When the burst is on a hot water pipe
A burst on the hot side needs extra care. Hot water can scald, and the hot water system keeps trying to refill and reheat while the water is escaping. Turn the system off as well as the water: switch off the power to an electric or heat pump unit at the switchboard, or turn a gas unit to off. Don't turn it back on until the pipe is fixed and the tank is full again, or an electric element can burn out.
In many older Maroubra homes, the hot water pipes run outside along the walls to the tank down the side of the house. Those exposed copper pipes cop the sun and, near the beach, the salt air. Insulating them reduces heat loss and protects them. See insulating hot water pipes.
What not to do with a burst pipe
- Don't wrap it in tape and turn the water back on. Tape won't hold at mains pressure for long, and the next failure may happen when no one is home.
- Don't use power points or switches that are wet or near water. Turn the power off at the switchboard first.
- Don't leave water sitting in ceilings. A sagging ceiling can come down. Keep people out of the room and put a bucket underneath.
- Don't ignore a small leak. A slow drip inside a wall can rot timber, damage plaster and grow mould long before you see it.
After the repair: drying out and insurance
Once the pipe is fixed, the next job is drying things out. Open windows, run fans, and pull back wet carpet and underlay so the floor can dry. Wet plasterboard ceilings usually need replacing if they've sagged or stained. Take photos of the damage before you clean up, and keep any damaged items until your insurer has seen them.
If you're making an insurance claim, we can give you a written report of what failed and what we did, with photos. Insurers usually want to know the cause, so the more detail you have, the easier the claim.
How we repair burst pipes in Maroubra
- Make it safe. We make sure the water is off and check that power and appliances near the leak are safe.
- Find the leak. If the burst isn't obvious, we use pressure testing, listening equipment and a thermal camera to pinpoint it, so we only open up the wall, floor or ground where we need to.
- Give you options. A single split pipe can be cut out and repaired. A run of old galvanised pipe that's failing in several places is usually better replaced. We explain both and give you a fixed price for each before any work starts.
- Repair or replace. We repair with copper or modern pressure pipe, using proper fittings, and support and protect the pipe so it isn't rubbing or strained.
- Test it. We turn the water back on slowly, check for leaks under pressure and check the flow at the taps.
- Clean up. We tidy up the work area and explain what to do about any wall or ceiling damage.
Split and pinholed pipes
Copper and galvanised pipes cut out and repaired with new pipe and fittings.
Water service replacement
The pipe from the meter to the house replaced when it's old, leaking or too small.
Repiping old galvanised
Rusting galvanised pipe replaced with copper or modern pipe, so you're not waiting for the next burst.
Flexi hoses
Burst or worn flexible hoses under sinks, basins and toilets replaced with quality hoses.
Pressure limiting valves
Valves fitted at the meter to bring high mains pressure down and protect pipes and appliances.
Leaks in walls and under floors
Hidden leaks found with leak detection equipment and repaired with as little damage as possible.
What to expect when we come out
When you call, we'll ask where the water is coming from, whether you've been able to turn it off, and whether it's on the hot or cold side. That helps us bring the right pipe and fittings so most repairs are finished in one visit. We give you a time window and let you know when we're on the way.
On site we protect the floors, find the leak and show you what's failed before we quote. Once you've chosen an option, we get on with it, test the repair under pressure and clean up before we leave. If the leak has been running for a while, we'll also check the water meter afterwards so you can be sure there isn't a second leak somewhere else.
Signs your Maroubra home needs repiping
Fixing one leak is often all you need. But if your home has several of these, it may be time to replace the old pipes rather than keep patching them:
- Two or more leaks or bursts in the past few years.
- Rusty, brown or discoloured water when you first turn on a tap. See brown hot water.
- Poor pressure at every tap that has slowly got worse.
- Visible galvanised pipe (grey, threaded joints) under the house or at the meter.
- Patches and repairs in several different pipe materials.
Patch it or replace the pipe?
| Situation | Usually a repair | Usually worth replacing |
|---|---|---|
| One split in copper pipe | Cut out the damaged section and join in new pipe | Only if the rest of the pipe is thin or pinholed |
| Burst in old galvanised pipe | A short-term repair to get the water back on | The galvanised run, before it bursts somewhere else |
| Leak in the yard from the meter | Repair the leaking joint | The whole water service if it's old, shallow or has leaked before |
| Burst flexi hose | Replace that hose | All the old hoses in the house at the same time |
| Leaks after banging pipes | Fix the leaking fitting | Add a pressure limiting valve and secure loose pipes |
What affects the cost of a burst pipe repair
We always quote on site once we've found the leak. The things that change the price most are:
- Where the pipe is. A pipe under a sink is quick to reach. One inside a tiled wall, under a slab or under a driveway takes more work.
- How easy it is to find. An obvious burst needs no detection. A hidden leak may need leak detection equipment first.
- Repair or replacement. Fixing one split is a small job. Replacing an old galvanised run or the whole water service is a bigger one, but it stops the next burst.
- Access. Tight side passages, low floors and concrete all add time.
- Making good. We'll tell you if you'll need a plasterer, tiler or concreter for the finish, so you can plan for it.
You'll have a fixed price for each option before we start.
Who's responsible for a burst pipe?
- Sydney Water looks after the water main in the street and the water meter. If the leak is at the meter or on the street side of it, call Sydney Water.
- You (the homeowner) are responsible for the pipes on the house side of the meter: the water service across the yard and all the pipes inside the home.
- In units and townhouses, pipes inside your own unit are usually yours. Shared pipes in common areas usually belong to the building.
If you're not sure which side of the meter the leak is on, we can check it for you. Our water meter guide shows how to read your meter and test for a leak.
A quick leak check you can do
- Turn off every tap, and make sure the washing machine, dishwasher and irrigation aren't running.
- Find your water meter and write down the reading, or take a photo.
- Don't use any water for 30 to 60 minutes.
- Read the meter again. If the numbers have moved, water is leaking somewhere.
- Turn off the main stop tap and check again. If the meter still moves, the leak is between the meter and the stop tap; if it stops, the leak is inside the property.
Our water meter leak test post walks through it step by step.
Our recent burst pipe work near Maroubra
Burst water pipe repaired, Matraville
The problem: a water pipe had burst at a home in neighbouring Matraville, a few minutes from Maroubra.
What we did: we found the burst and repaired it with new copper pipe.
The result: the water was back on with a sound repair in new copper.


More local jobs are on our recent projects page.
How to protect your pipes
- Know where your stop tap is and check it turns. A seized stop tap makes a burst much worse.
- Replace flexi hoses that are rusty, kinked or more than about ten years old.
- Check your water pressure. If taps bang or the hot water relief valve drips a lot, the pressure may be too high.
- Plan to replace galvanised pipe before it fails, rather than after a flood.
- Keep trees away from the water service between the meter and the house.
What happens when you call
Tell us what's going on
Call or send a quick form. A photo of the problem helps us come prepared. No call-out fee.
Options and a fixed price first
We find the cause, explain your options and give you a fixed price for each before any work starts.
Fixed, tested and backed
We do the work, test it, clean up, and back our workmanship with a lifetime labour warranty.
Why Maroubra homeowners call us
- Based in Matraville, a short drive from every part of Maroubra
- Rated 5.0 from 110 Google reviews
- Free quotes, with options and a fixed price before any work starts
- Lifetime labour warranty on our workmanship
- Licensed plumbers, drainers and gasfitters (Lic. 398171C)
Burst pipe questions from Maroubra homeowners
What should I do first if a pipe bursts?
Turn off the water at the main stop tap, usually at the meter near the front boundary. Turn off the hot water system and the power near any water, then call us.
Where is the water meter on a Maroubra house?
Usually near the front boundary, in the front garden or beside the path. In semis it's often at the front of each half, and in units it may be in a meter cupboard.
Is a leak at the water meter my problem?
Leaks at the meter or on the street side of it are Sydney Water's responsibility. Leaks on the house side of the meter are the homeowner's.
Can you find a leak without digging up the yard?
Usually, yes. We use pressure testing, listening equipment and a thermal camera to find the leak first, so we only dig or open up where the leak is.
Should I replace all my galvanised pipes?
If one galvanised pipe has burst, the rest is usually in similar condition. We can repair the burst and give you a fixed price to replace the rest, so you can decide.
Why do my pipes bang when I turn off a tap?
That's water hammer, often caused by high pressure or loose pipes. A pressure limiting valve and properly secured pipes usually fix it.
Will my home insurance cover a burst pipe?
Many policies cover damage caused by a sudden burst, but not always the pipe repair or slow leaks. Check your policy. We can give you photos and a written report of what we found.
How long does a burst pipe repair take?
Most repairs to a single pipe are done in a couple of hours. Replacing a water service or a run of old pipe can take a day or more, depending on access.
More plumbing in Maroubra: our Maroubra plumber page, leak detection, hot water, tap repair, toilet repair, stormwater and sewer repairs. Nearby: Matraville, Malabar and South Coogee. Guides: hidden water leaks, water pressure and galvanised pipes.