Gas fitting in Hillsdale 2036
Gas is part of everyday life in a lot of Hillsdale homes: a gas cooktop in the kitchen, a heater plugged into a bayonet in winter, a continuous flow unit on the balcony. In the three-storey unit blocks that make up most of the suburb, gas lines often run between units and meters are grouped together, so knowing what's yours matters. In the post-war cottages, gas pipe under the floor may be decades old. Here's what's involved in getting gas work done safely in Hillsdale.
Gas work we do in Hillsdale
Cooktops and ovens
New cooktops and ovens connected, or old ones swapped, with approved fittings and a pressure test.
Heater bayonets
Bayonets added or moved so a portable heater can sit where you need it.
Gas hot water
Storage and continuous flow units connected or replaced, with the supply sized for them.
Continuous flow faults
Error codes, ignition and flame faults diagnosed and repaired.
Leak checks
The whole system pressure tested to confirm it's sound.
Capping off
Old points capped and tested when appliances go electric.
Signs you need a gasfitter
- A gas smell near an appliance or the meter.
- Yellow or lifting flames on the cooktop.
- Soot above a heater or around a hot water flue.
- A continuous flow unit showing an error code or running lukewarm.
- A pilot light that won't stay lit.
- A cracked hose behind a freestanding oven.
- A gas bill that jumps without reason.
If you can smell gas strongly, turn the gas off at the meter, open doors and windows, don't use switches or flames, and leave. Call Jemena, who look after the gas network, from outside, then call us for anything on your side of the meter.
Why gas jobs come up in Hillsdale
Grouped meters in unit blocks
Hillsdale's unit blocks usually have their gas meters grouped together, often near the entrance or in a meter room. Each unit's line runs from its meter through the building to the kitchen and hot water. Before any work, we confirm which meter and line are yours. If the labels have faded, we work it out and mark it.
Old gas pipe in post-war cottages
Many of Hillsdale's cottages were built after the war, some by the Housing Commission. Their gas lines run under timber floors, and over the decades branches have been added, moved and capped. Old capped ends and joints are where small leaks hide, so we test the whole line before connecting anything new.
Continuous flow in small spaces
Continuous flow units on Hillsdale balconies and outside walls give endless hot water and save space, but they need enough gas while they run and the right flue clearances. When one is replaced, the new one has to meet current clearance rules, which can mean a slightly different spot.
Cooktops and the gas supply
A modern cooktop with a wok burner can need more gas than the old one. In a unit where the cooktop and continuous flow hot water share a line, one can starve the other. We check the pipe size and regulator before connecting.
Hillsdale homes and their gas
| Home type | What we usually find | What to think about |
|---|---|---|
| Three-storey unit blocks | Grouped meters, lines through the building, cooktops and continuous flow | Which meter and line are yours, flue clearances |
| Post-war cottages | Old lines under timber floors, gas hot water down the side | Test the whole line first |
| Housing Commission homes | Original gas lines with later changes | Capped branches, old joints |
| Newer apartments near Southpoint | Modern lines, building-managed supplies | Building rules, shared supplies |
How a gas job runs
- Tell us what you need. A photo of the appliance and its data plate helps.
- Check the system: meter, regulator, pipe size and condition, with a pressure test.
- Options and fixed prices.
- Do the work with approved pipe and fittings and isolation valves.
- Test and commission: pressure test, joints checked, appliances lit and set.
- Certificate of Compliance for the gas work.
Cooktops and ovens in Hillsdale units
Hillsdale unit kitchens are often compact, with the cooktop close to a wall or window. A new cooktop needs the right clearances to the rangehood and side walls, a connection that won't strain when someone leans on the bench, and enough gas for every burner. For a freestanding oven, we fit a new approved hose and a restraint so the oven can't be pulled far enough to strain the connection. See gas cooktop installation.
Heaters and bayonets
Plenty of Hillsdale homes use a portable gas heater in winter, plugged into a bayonet. Older units often have one bayonet in a spot that suited the furniture decades ago. We can move it or add another. Have heaters serviced before winter, keep room vents clear, and consider a carbon monoxide alarm if you use a gas heater indoors. See gas bayonet installation.
Continuous flow hot water
Continuous flow units show an error code when something goes wrong: ignition, flame failure, overheating, a fan or a sensor. Write the code down and tell us when you call, with the brand and model. Sometimes the cause is the gas supply when another appliance is running; sometimes it's a worn part. Don't keep resetting a unit with flame or overheat codes. See hot water in Hillsdale.
Repair, extend or new line?
| Situation | Repair or extend | New line |
|---|---|---|
| Small leak at one joint | Repair and retest | Not needed |
| One new appliance, line big enough | Extend | Not needed |
| Cooktop and hot water starving each other | Upgrade part of the run if possible | Often a new line from the meter |
| Old line with several leaks | Short-term only | Usually better |
| Kitchen moved | Rarely | A new run |
What affects the cost
- The appliance and whether it's a swap or new.
- Distance from the meter, which in a unit block can be several floors.
- Access through the building or under a timber floor.
- Pipe size and regulator upgrades.
- Making good.
You get a fixed price for each option before any work starts.
Who's responsible?
- Jemena: the gas network, service and meters.
- You: pipework and appliances serving your home.
- Unit blocks: shared lines, meter rooms and common flues are usually the owners corporation's.
- Your retailer: your gas account.
Safety checks you can do
- Know which meter is yours and how to turn it off.
- Look at your cooktop flames: blue with a small steady tip.
- Check for soot around heaters and the hot water flue.
- Keep vents and the area around the hot water unit clear.
- If a smell comes and goes, note when and where, and call us.
Signs it's urgent and when it can wait
- Act straight away if the gas smell is strong: turn off at the meter, get out, call Jemena, then us.
- Call soon if there's a faint smell, yellow flames, soot or no hot water.
- Book a time if you're planning a new cooktop, heater point or hot water change.
A recent gas job nearby
Here's a recent gas hot water job nearby in Maroubra.
Gas storage tank replaced with continuous flow, Maroubra (nearby)
The problem: an old gas storage tank beside a Maroubra home had stopped delivering hot water.
What we did: we explained repairing against replacing and the systems that would suit, and the owners chose a Rinnai continuous flow unit. We removed the tank, mounted the new unit on the wall, upsized the copper pipework and replaced the gas regulator at the meter so the new unit gets enough gas.
The result: reliable hot water throughout the house, on a properly sized gas supply.


More local work is on our recent projects page.
“Great plumber, fixed my leaking taps quickly and at a great price!”
Tom (Google review)
Gas across Hillsdale
- Unsted Crescent and the unit streets: grouped meters and continuous flow on balconies.
- Rhodes Street and the cottage streets: older lines under timber floors and gas hot water down the side.
- Along Bunnerong Road: newer apartments near Southpoint with building-managed supplies.
- Near Wentworth Avenue: homes close to Eastgardens.
- Near Matraville Public School: older homes shared with Matraville.
Gas in older unit blocks
In some of Hillsdale's post-war blocks, the gas pipework inside the building is as old as the building. Each unit's line may run along a common wall or through a shared service duct before reaching the kitchen. Work on the shared part of the system is a matter for the owners corporation, but the line from your meter into your unit, and everything after it, is usually yours. If we find a problem in a shared section, we'll tell you and give a report you can pass on.
Going electric?
Some Hillsdale owners are replacing gas cooktops with induction, gas heaters with reverse-cycle air conditioning, and gas hot water with electric or heat pump systems. If that's your plan, we can tell you which gas appliances can stay for now, cap off the rest safely, and test the line. When the last gas appliance comes out, talk to your retailer and Jemena about the meter. In a unit block, check whether the building has any rules about removing gas.
Buying a unit or cottage?
Before you buy, ask the age of the hot water system and whether the gas appliances have been serviced. A gas pressure test confirms the system is sound. It's quick and gives you peace of mind before you move in.
Questions to ask any gasfitter
- Are you licensed for gasfitting? Our licence is 398171C.
- Will you pressure test the whole system?
- Will I get a Certificate of Compliance?
- Is the price fixed?
- What warranty comes with the work? Ours is a lifetime labour warranty.
Looking after gas appliances
- Service gas heaters every year or two.
- Keep cooktop burners clean.
- Check the hose behind a freestanding oven.
- Keep the area around the hot water unit clear.
- Fit a carbon monoxide alarm if you use a gas heater indoors.
Gas words explained
- Bayonet: a socket for a portable heater.
- Regulator: sets the gas pressure for your home.
- Pressure test: shows whether the system holds pressure.
- Flue: the outlet for combustion gases.
- Continuous flow: a unit that heats water as it's used.
- Certificate of Compliance: the paperwork recording the gas work.
Running a new gas line in a unit block
When a unit's gas line needs replacing or upsizing, the route matters. The line usually starts at the meter bank, runs up or along the building, and enters the unit near the kitchen or hot water. Some of that route may be through common property, which means talking to the owners corporation before work starts. We plan the route with you, tell you which parts need building approval, and keep new pipe neat, clipped and protected. The rest of the work inside your unit is straightforward.
Gas lines under cottage floors
Hillsdale's cottages, including the Housing Commission homes built after the war, were plumbed for gas when they went up, and most have had the system changed a few times since: a stove point moved when the kitchen was updated, a heater point added, a hot water unit swapped. The result is often a line that's part original steel, part newer copper, with dead ends nobody remembers. Before we connect a new appliance to a system like that, we pressure test the whole line, so a weak joint in an old section is found by us rather than by a gas smell later.
Replacing a continuous flow unit, step by step
- Check the old unit's model, the gas pipe size, the regulator and the flue clearances.
- Confirm the new unit's gas and water flow needs.
- Isolate gas, water and power, and remove the old unit.
- Mount the new unit and connect water, gas and power, upgrading the gas pipe or regulator if needed.
- Purge, pressure test and fire up the unit.
- Set the temperature, test every tap and the controllers, and show you how to use them.
- Hand over the Certificate of Compliance.
Gas or induction?
| Gas cooktop | Induction cooktop | |
|---|---|---|
| Feel | Instant visible flame, good for woks | Fast and precise |
| Installation | Gas point and approved connection | Dedicated electrical circuit |
| Cookware | Anything | Induction-compatible pans |
| Cleaning | Burners and trivets | Flat glass |
| In a unit | Needs a gas supply | Needs enough electrical capacity |
We install and service gas cooktops, and cap off the gas point safely if you change to induction.
Gas heaters and ventilation
In a compact Hillsdale unit, a gas heater needs good ventilation. Don't block wall vents or seal up a room completely while a portable heater is running. Have the heater serviced before winter: a service checks the burner, the safety cut-outs and that it's burning cleanly. If a heater is very old, parts may not be available, and a flued heater or electric heating may be safer. We'll tell you what we find.
Small jobs, done properly
A lot of gas work in Hillsdale is small: swapping a cooktop, replacing a perished oven hose, moving a bayonet, capping off an old heater point. Small doesn't mean less care. Every job gets a pressure test, every joint is checked, and every appliance we connect is lit and checked before we leave.
Balcony units and building rules
Many Hillsdale unit blocks have rules about what can go on a balcony or an outside wall, and some require approval for changes to external appliances. If you're replacing a continuous flow unit in the same spot, approval usually isn't an issue. If you're moving it, adding a new flue, or putting a gas BBQ point on a balcony, check with your owners corporation first. We can give you the details they'll need.
Gas BBQs on balconies and courtyards
A fixed natural gas point for a barbecue is safer and easier than swapping bottles, but on a Hillsdale balcony or small courtyard it needs careful placement: clear of windows, doors, eaves and anything that could catch, and allowed under your building's rules. A barbecue made for bottled gas must be converted before it's connected to natural gas. We'll check the space and give you a fixed price.
Why the regulator matters
The regulator at the gas meter sets the pressure that reaches your appliances. If it's too small for a new continuous flow unit or a big cooktop, the appliances will struggle even if the pipe is big enough. When we upgrade a hot water system or a cooktop, we check the regulator, and if it needs replacing, we arrange it as part of the job.
When the cooktop won't light
If one burner won't light but the others do, the igniter or burner is usually dirty or worn. If none will light and the hot water still works, the cooktop's isolation valve may be off or its ignition has failed. If no gas appliance works, check the meter valve and whether the supply has been interrupted. Don't keep clicking a burner that won't light. Turn it off, let any gas clear, and call us if it doesn't come good.
Moving a gas appliance
Owners sometimes want the cooktop moved when a kitchen is updated, or the hot water unit moved away from a bedroom window. Each move means a new gas run sized for the appliance and, for hot water, new water and power connections and a flue that meets the rules. In a unit, moving anything on an outside wall may need building approval. We'll tell you what's practical before you commit.
Servicing a continuous flow unit
A service every couple of years checks the burner, fan and flue for dirt and insects, cleans the water inlet filter, checks the gas pressure and tests the safety cut-outs. On Hillsdale balconies, where units can be crowded by stored items and plants, clearing space around the unit prevents many faults. If your unit is making new noises, taking longer to deliver hot water or showing occasional codes, a service is a good first step.
Before you call
- What's the appliance, and what's it doing?
- Brand and model, from the data plate.
- Any error code.
- House, unit, or apartment above Southpoint?
- Which meter is yours, if you know.
Gas safety in shared buildings
In a unit block, a gas problem in one home can affect others. If you smell gas in a stairwell, a meter room or a common area, don't try to find it yourself. Don't use light switches or lifts near the smell, get people out, and call Jemena from outside. Then let the building manager or owners corporation know. If the smell is inside your unit, turn your meter off if you can reach it safely, ventilate and leave. We can then find and fix any fault on your side of the meter.
Gas hot water in cottages
Gas storage tanks down the side of Hillsdale cottages last around ten years. When one fails, the options are another storage tank, a continuous flow unit, or a heat pump. A like-for-like tank usually connects straight to the existing gas. Continuous flow often needs a bigger line and regulator. A heat pump means the gas to the hot water is capped. We'll price each so you can compare.
Old heater points nobody uses
Many Hillsdale units and cottages have an old gas heater point or bayonet that hasn't been used in years, sometimes hidden behind furniture or painted over. An unused point that's in good condition is safe, but one that's damaged, loose or leaking isn't. If you don't plan to use it, it can be capped off properly and tested. If you'd like to use it again, we'll check it first. It's a quick job that removes a forgotten risk.
What happens when you call
Tell us what's going on
Call or send a quick form. A photo of the problem helps us come prepared. No call-out fee.
Options and a fixed price first
We find the cause, explain your options and give you a fixed price for each before any work starts.
Fixed, tested and backed
We do the work, test it, clean up, and back our workmanship with a lifetime labour warranty.
Jobs we finished recently

Why Hillsdale homeowners call us
- Based in Matraville, around the corner from Hillsdale
- Rated 5.0 from 110 Google reviews
- Free quotes, with options and a fixed price before any work starts
- Lifetime labour warranty on our workmanship
- Licensed plumbers, drainers and gasfitters (Lic. 398171C)
Gas fitting questions from Hillsdale homeowners
Do I need a licensed gasfitter to connect a cooktop?
Yes. In NSW gas work must be done by a licensed gasfitter and certified.
Which gas meter is mine in our block?
It should be labelled with your unit number. If not, we can identify it.
My continuous flow unit shows an error code. Can you fix it?
Often. Tell us the code, brand and model.
Why does my hot water go cold when the cooktop is on?
The gas supply may be too small for both. We can check and upgrade it.
Can you move my gas bayonet?
Yes, or add another.
Who fixes a leak at the meter?
Jemena.
Do you work in unit blocks?
Yes, on the gas serving your own unit. Shared lines are the owners corporation's.
My cooktop flames are yellow. Is that a problem?
Yes. Stop using that burner and have it checked.
Can you cap off gas if I go electric?
Yes, and test the line.
How long does a cooktop swap take?
Usually a couple of hours.
What's a Certificate of Compliance?
The paperwork confirming the gas work meets the standards.
Should I have my gas checked before buying?
It's a good idea. A pressure test is quick.
More plumbing in Hillsdale: our Hillsdale plumber page, hot water and blocked drains. Nearby: gas fitting in Pagewood and Matraville. Guides: gas fitting, gas compliance certificates and gas point installation.