Tap repairs in Banksmeadow 2019
Taps on a work site do a lot more than taps at home. A lunchroom mixer is turned on and off all day. Basin taps in the amenities are used by workers with grease or dust on their hands. Hose taps on loading docks get hit by forklifts, left running and baked in the sun and salt air off Botany Bay. A dripping tap is easy to ignore, but on a site with dozens of them, the water adds up, and a tap that won't turn off when you need it is a real problem. We're based a few minutes away in Matraville.
Taps we repair in Banksmeadow
Basin mixers
Dripping, stiff or loose mixers in amenities and offices, with new cartridges or new mixers.
Lunchroom and kitchenette mixers
Sink mixers that drip, swivel loose or won't hold temperature.
Push-button and sensor taps
Taps that run on, won't start or drip, repaired or replaced.
Change room shower mixers
Shower mixers worn by heavy use, serviced or replaced.
Hose taps and wash points
Hose taps that drip, seize or get knocked off, replaced with heavy-duty taps.
Older washer taps
Two-handle taps in older buildings and homes, rewashered with re-cut seats.
Signs a tap needs repairing
- Drips from the spout after the tap is turned off.
- Water leaking from around the handle or the base.
- A handle that's stiff, loose or spins without turning the water off.
- A mixer that won't hold a steady temperature.
- A sensor or push-button tap that runs on, won't start or won't stop.
- A hose tap that's seized, bent or dripping from its spindle.
- Low flow from a tap that used to run well.
Why taps wear out on Banksmeadow sites
Constant use
The lunchroom mixer and the basin taps in the amenities may be used hundreds of times a day. The ceramic disc cartridges in mixers are tough, but they wear, crack and pick up grit, and the O-rings around them dry out and leak.
Grit in the water
Sand and grit in the water supply scratch ceramic discs and lodge under washers, so taps drip even when they're new. It's common after work on the mains or the site's own water service.
Salt air
Taps outdoors on yards and docks, and on walls facing the bay, corrode faster. Brass goes green, spindles seize, chrome pits and handles crack.
Hard knocks
Hose taps on risers along docks and driveways get hit by forklifts, pallets and trucks. A bent spindle or a cracked body means the tap won't turn off properly, and a riser that's been hit can leak underground.
Banksmeadow sites and their taps
| Where | Typical taps | Common problems |
|---|---|---|
| Amenities | Basin mixers, push-button taps | Worn cartridges, taps running on |
| Lunchrooms | Sink mixer, boiling water unit, filter tap | Dripping, loose swivel, low flow |
| Change rooms | Shower mixers, basin taps | Worn cartridges, wandering temperature |
| Yards and docks | Hose taps, wash points | Seized or knocked-off taps, corrosion |
| Homes near Botany | Washer taps, mixers, garden taps | Worn washers, corroded garden taps |
How we repair a tap
- Tell us which taps and what they're doing, and send a photo if you can so we know the brand.
- Isolate the water at the tap's valve, or at the meter if there isn't one.
- Take the tap apart and find the worn part: cartridge, washer, O-ring, seat or spindle.
- Repair it with the right part. For washer taps, we re-cut the seat so the new washer seals properly.
- Or replace it if it's worn out, cracked or not suited to the use it gets.
- Test it and check for leaks around the base and under the bench.
A recent tap job nearby
Here's a recent job in Maroubra where leaking taps were fixed on the same visit as a drain clear.
Leaking taps fixed during a drain clear, Maroubra (nearby)
The problem: a Maroubra home had leaking taps as well as slow drains.
What we did: we laid a mat to protect the floor, jetted the drains and floor wastes clear, and then repaired the leaking taps on the same visit.
The result: the taps shut off properly and the drains flow freely, all in one visit.


More local work is on our recent projects page.
Quick fix or long-term fix?
| Problem | Quick fix | Long-term fix |
|---|---|---|
| Dripping mixer | New cartridge | Commercial-grade mixer if it keeps wearing out |
| Dripping washer tap | New washer and re-cut seat | Replace with a mixer if the tap body is worn |
| Seized hose tap | Free it or replace it | Heavy-duty hose tap on a guarded riser |
| Push-button tap running on | Service the timing cartridge | Replace with a new push-button or sensor tap |
| Taps dripping from grit | Replace the parts | Fit a strainer on the incoming supply |
What affects the cost
- The type and brand of tap, and whether parts are available.
- How many taps need work.
- Whether the tap needs replacing rather than repairing.
- Access: taps in tight cupboards or walls.
- Timing: outside your business hours.
You get a fixed price before any work starts.
Who's responsible?
- The site owner or tenant: taps in and around the building. Check your lease.
- Factory complexes: taps in each unit usually belong to that unit; shared hose taps on the roadway may be the complex's.
Quick checks you can do
- Turn each tap off firmly and watch the spout for a minute.
- Look under basins and sinks for drips or damp.
- Check that each tap has a working isolation valve underneath.
- Try every hose tap to make sure it turns off fully.
- Check outdoor taps for green corrosion or bent spindles.
Signs it's urgent and when it can wait
- Call straight away if a tap won't turn off and you can't isolate it, or a hose tap has been knocked off and water is pouring.
- Call soon if a tap is leaking under a bench or a shower mixer won't hold temperature.
- Book a time if a tap is dripping or stiff.
Push-button and sensor taps
Push-button taps run for a set time and turn themselves off, and sensor taps run only while hands are under them. Both save water in busy amenities and mean nobody needs to touch a handle with dirty hands. When a push-button tap runs on or a sensor tap won't start, the timing cartridge, solenoid or sensor may need servicing or replacing. We repair the common brands and replace taps that are past repair.
Hose taps that stand up to an industrial yard
A domestic garden tap doesn't last long on a loading dock. We fit heavy-duty hose taps with a vacuum breaker, which stops dirty water being drawn back into the supply if pressure drops, and can mount them on a guarded riser or move them to a spot out of the forklift path. For wash-down areas, we can fit lockable or loose-key taps so they aren't left running.
Taps in older buildings
Older industrial buildings and homes on the Botany side can still have two-handle washer taps. A drip usually means a worn washer, but if the brass seat underneath is pitted, a new washer alone won't seal for long. We re-cut the seat so the new washer seals properly. If the tap body is worn or the handles strip, we'll suggest a new mixer.
Banksmeadow, area by area
- Industrial estates off Botany Road: factory units with an amenities basin and a kitchenette sink.
- Warehouses and logistics yards: change rooms, wash points and hose taps on docks.
- Near the port and the bay: outdoor taps in salty air.
- The Botany side: homes and units with older washer taps and garden taps.
- Next door in Botany, Hillsdale and Matraville: we fix taps here every week.
Tap words explained
- Cartridge: the part inside a mixer that controls flow and temperature.
- Washer: the rubber disc that seals a traditional tap.
- Seat: the brass surface the washer presses against.
- Spindle: the shaft that turns when you turn the handle.
- Vacuum breaker: stops dirty water being drawn back into the supply through a hose tap.
- Isolation valve: a small valve under a basin or sink that turns off one tap.
Homes in Banksmeadow
For the homes and units on the Botany side of Banksmeadow, we repair dripping washer taps and mixers, replace corroded garden taps and fit new tapware, just as we do in Botany. See tap repairs in Botany.
What a dripping tap costs a business
One dripping tap doesn't seem worth a call-out. But a steady drip can waste a surprising amount of water over a year, and on a site with a dozen basins, a lunchroom sink, a change room and a row of hose taps, a few drips at a time become a real line on the water bill. A tap that leaks under the bench is worse: the water soaks into cabinets and floors where nobody sees it until the damage is done. Fixing taps as they start to drip is cheaper than fixing the damage later.
Repairing a mixer, step by step
- We turn off the water at the mixer's isolation valves under the basin or sink.
- The handle and cover come off, and we take out the cartridge.
- We check the cartridge, the O-rings and the seat in the tap body for wear, cracks and grit.
- A new cartridge of the right type goes in, with new O-rings if they're worn.
- We reassemble the tap, turn the water back on and test the flow, the temperature and the shut-off.
- We check under the bench for leaks at the flexible hoses and replace any that are corroded.
Most mixer repairs are done in one visit. Some brands use cartridges we need to order, and we'll tell you if that's the case.
Lunchroom sinks
The lunchroom sink is often the hardest-working tap on a site. It fills kettles, rinses mugs and lunch boxes, and gets swung from side to side all day. Swivel spouts work loose and leak at the base, and cartridges wear. If your lunchroom also has a boiling water unit or a filter tap, we'll check those while we're there, since they often share the same isolation valves and hoses under the sink. See water filters in Banksmeadow.
Shower mixers in change rooms
Shower mixers in a change room are used at the same time every day, at shift change, by people who want hot water fast. Cartridges wear, and the temperature starts to wander. If the shower is protected by a thermostatic mixing valve, the TMV itself may need servicing. We repair or replace the mixer, check the TMV, and set the temperature so it's comfortable and safe. See TMV testing.
Isolation valves under every tap
Every basin and sink should have isolation valves underneath, so one tap can be turned off without shutting the whole building. On older sites they're often missing or seized. When we find that, we fit new ones. It makes this repair quicker and every future repair easier, and it means a tap that won't turn off can be stopped in seconds instead of minutes.
Choosing taps for a busy site
| Where | Tap that suits | Why |
|---|---|---|
| Amenities basins | Push-button or sensor tap | Turns off by itself, no handle to touch with dirty hands |
| Lunchroom sink | Commercial-grade sink mixer with a high spout | Fills kettles and jugs easily, lasts longer |
| Change room showers | Commercial-grade mixer with a TMV | Holds temperature and stands up to daily use |
| Yards and docks | Heavy-duty hose tap with vacuum breaker | Survives knocks and protects the water supply |
| Wash-down points | Loose-key or lockable tap | Stops taps being left running |
Hose taps on risers
Hose taps on a dock or yard often sit on a short pipe riser coming out of the ground. When a forklift or truck clips one, the damage isn't always just the tap. The riser can bend or crack below ground, and that leak can run into the sand for weeks. When we replace a knocked hose tap, we check the riser and the pipe below, and if the tap is in a traffic path, we'll suggest a bollard, a steel guard or a better spot for it.
Low flow from a tap
If a tap that used to run well now trickles, the aerator in the spout may be blocked with grit or scale, the isolation valve underneath may be partly closed or failing, or on older sites the galvanised pipe feeding the tap may be narrowing from rust inside. We clean or replace aerators, replace failing valves, and if the pipe is the problem, we'll explain the options for replacing it.
Taps and backflow
Any tap that can have a hose attached is a possible way for dirty water to get back into the supply, for example if a hose is left in a bucket of chemicals or a wash tub when pressure drops. That's why hose taps on industrial sites should have a vacuum breaker, and why some sites need a backflow device on wash-down points or at the boundary. If you're not sure your site has the right protection, ask us. See backflow testing in Banksmeadow.
What to tell us when you call
- Which taps are affected and where they are.
- What they're doing: dripping, leaking under the bench, stiff, running on or seized.
- The brand if you can see it on the tap.
- Whether each tap has its own isolation valve.
- When the amenities or lunchroom are quietest.
A recent kitchen tap job
At a unit on Daunt Avenue in Matraville, a short drive from Banksmeadow, we replaced a kitchen mixer the owners had chosen, along with the mini stop taps under the sink. On the same visit we drilled the stone benchtop and fitted a separate filter tap, with the filters mounted under the sink and connected to the cold water, and fitted new flexible hoses on the bathroom basin mixers. Doing all the taps in one visit meant the water was only off once.
Taps in salty air
Banksmeadow is right on Botany Bay, and outdoor taps here take a beating from the salt in the air. Chrome pits, brass turns green and crusty, and spindles seize so tightly the handle snaps before the tap turns. When we replace outdoor taps, we use heavier fittings that cope better near the coast, and we can fit them with loose keys or lockable handles on sites where taps get left running. A little silicone grease on spindles once a year keeps them turning.
When to replace instead of repair
- The tap body is cracked or badly corroded.
- Parts for the brand are no longer available.
- The tap has been repaired several times and keeps failing.
- The tap doesn't suit the use it gets, such as a domestic mixer in a busy amenities block.
- You want to save water with push-button, sensor or flow-limited taps.
We'll give you a fixed price for both repair and replacement where either makes sense, so you can choose.
Flexible hoses under basins and sinks
Most mixers are connected to the pipes by braided flexible hoses hidden in the cupboard or behind the basin. They're under mains pressure all the time, and near the bay their stainless braid can corrode. A hose that bursts in an office kitchenette or an upstairs amenities block can flood the floor, and the unit below, in minutes. Whenever we repair or replace a tap, we check its hoses. If they're rusty, frayed, kinked or more than a few years old, we replace them at the same time. See flexi hose replacement.
Checking every tap on site
On a site with many taps, it's often cheaper to check and fix them all in one visit than to call us out each time one starts dripping. We go through every basin, sink, shower and hose tap, note what's worn, and give you a fixed price to fix the lot. We can do it on a quiet day or a Saturday so nobody's caught without water.
Taps and the water bill
If the water bill on your site has crept up, dripping taps are worth checking along with toilets. Walk the amenities, the lunchroom, the change room and the yard with everything turned off, and look and listen at each tap. Hose taps on the far side of the yard and basin taps in a little-used office are the easiest to miss. Then read the meter, wait an hour without using water and read it again. If it has moved, something is still running.
What happens when you call
Tell us what's going on
Call or send a quick form. A photo of the problem helps us come prepared. No call-out fee.
Options and a fixed price first
We find the cause, explain your options and give you a fixed price for each before any work starts.
Fixed, tested and backed
We do the work, test it, clean up, and back our workmanship with a lifetime labour warranty.
Jobs we finished recently


Why Banksmeadow businesses and homeowners call us
- Based in Matraville, a few minutes from Banksmeadow
- Weekend and early starts when that keeps your site running
- Rated 5.0 from 110 Google reviews
- Options and a fixed price before any work starts
- Lifetime labour warranty on our workmanship
- Licensed plumbers, drainers and gasfitters (Lic. 398171C), with accredited backflow testers on the team
Tap repair questions from Banksmeadow businesses and homeowners
Do you repair taps in factories and warehouses?
Yes. We repair and replace taps in amenities, lunchrooms, change rooms, yards and wash areas at factories, warehouses, workshops and offices.
Can you come today?
We offer same-day service. Tell us if a tap won't turn off.
Is it worth repairing a dripping mixer?
Usually yes, with a new cartridge, if parts are available. If it keeps wearing out, a commercial-grade mixer is better.
Can you fix push-button and sensor taps?
Yes. We service and replace timing cartridges, solenoids and sensors, or replace the tap.
A forklift knocked off our hose tap. Can you fix it?
Yes. We replace it with a heavy-duty tap and can protect it with a guard or move it.
Why do our taps drip even when they're new?
Grit in the water can scratch cartridges and lodge under washers. A strainer on the incoming supply helps.
Can you fit taps that save water?
Yes. Push-button, sensor and flow-limited taps all cut water use in busy amenities.
Do you fit vacuum breakers on hose taps?
Yes. They stop dirty water being drawn back into the supply.
Can you work outside our business hours?
Yes. We can work early or on a weekend.
Can you replace all the taps in our amenities at once?
Yes. We'll give you a fixed price to replace them together.
Do you still look after homes in Banksmeadow?
Yes. We repair taps for the homes and units on the Botany side of Banksmeadow too.
Do you give a fixed price?
Yes, before any work starts.
More plumbing in Banksmeadow: our Banksmeadow plumber page, taps and toilets, toilet repairs and water filters. Nearby: tap repairs in Botany and Hillsdale. Guides: water pressure guide, flexi hose replacement and water meter guide.