★★★★★ 5.0 from 100+ Google reviews · Your Sydney Plumber

Tap repairs in Eastlakes 2018

We repair and replace taps in Eastlakes units and houses: worn tap cartridges and dripping mixers, washer taps in walk-up bathrooms and laundries, shower taps leaking behind tiles, rusty garden taps at brick houses, seized isolating valves and split flexi hoses. We re-cut worn tap seats, replace cartridges, O-rings and spindles, and fit new tapware when a repair won't last. You get options with a fixed price for each before any work starts, backed by our lifetime labour warranty.

Worn tap cartridges are one of the most common calls we get from Eastlakes. Many of the walk-ups are from the 1960s and 70s, with a mix of original washer taps and later mixers, and a tap or hose that leaks in an upstairs unit can end up on the ceiling below. The red-brick houses have washer taps throughout and garden taps that have rusted over 50 or 60 years. We're a few minutes away in Matraville, and we fix the tap properly the first time.

Tap repairs we do

Dripping washer taps

New washers and re-cut seats so the tap shuts off cleanly.

Leaking mixers

Cartridges, O-rings and seals replaced, or the mixer replaced.

Shower taps and mixers

Spindles and cartridges replaced from the front, usually without removing tiles.

Laundry and garden taps

Seized, dripping and rusted taps repaired or replaced.

Stiff or loose handles

Spindles, cartridges and handle fixings replaced.

New tapware

Taps and mixers supplied and fitted to suit your basin, sink and benchtop.

Signs a tap needs repair

  • Drips from the spout after it's turned off.
  • Water at the handle or around the base.
  • Hard to turn, or needs a lot of force to stop.
  • Spins without stopping the water.
  • Squeals or shudders when turned on.
  • Low flow or a spluttering stream.
  • A loose handle or lever.
  • Damp in the cupboard under a sink or vanity.

Why taps fail in Eastlakes homes

Washer taps

Traditional washer taps close by pressing a rubber washer down onto a brass seat. Over the years, the washer hardens and the seat wears a groove. A new washer on a worn seat will drip again soon, which is why we re-cut the seat as part of the repair. Many Eastlakes brick houses and older units still have washer taps in the bathroom, laundry and garden.

Ceramic disc taps

Quarter-turn taps use two ceramic discs that slide over each other. They last a long time, but grit from old pipes can scratch the discs and cause a drip. We replace the ceramic cartridge with one that matches.

Mixer cartridges

Mixers use a single cartridge to control flow and temperature. After 10 to 20 years, the cartridge wears or the seals perish, and the mixer drips or gets stiff. Some imported mixers use cartridges that are hard to find; we identify the brand and model before ordering.

Old pipes and grit

In Eastlakes homes with some original galvanised pipe, rust and grit wash through and wear tap washers, seats and cartridges faster. A sediment filter or replacing the worst pipe runs helps. See galvanised pipes.

Water pressure

High pressure wears washers and cartridges faster and can make taps bang when they shut. A pressure limiting valve protects every tap in the home.

Eastlakes homes and their taps

Home typeTypical tapsCommon faults
1960s and 70s walk-upsMixers in kitchens, washer taps in bathrooms and laundriesWorn seats, dripping mixers, seized valves
Brick housesWasher taps throughout, some updated mixersWorn seats, rusted garden taps, stiff spindles
Former Brick houses with updated kitchensBasic washer taps, some replacementsOld parts, low flow from old pipes
Newer homes and apartmentsImported mixers, wall-mounted bath and shower mixersCartridges, hard-to-find parts

How we repair a tap

  1. Ask what's happening, and for a photo and any brand name.
  2. Turn off the water at the isolating valve or meter.
  3. Take the tap apart and find the worn part.
  4. Give you options: repair, convert or replace, each with a fixed price.
  5. Repair it properly: re-cut seats, new washers, O-rings, spindles or cartridges.
  6. Test it for drips, leaks and smooth operation.

Repair, convert or replace?

SituationUsually best
Washer tap with a sound bodyRepair with a new washer and re-cut seat
Washer taps you'd like easier to useConvert to quarter-turn ceramic spindles
Mixer dripping, cartridge availableNew cartridge
Mixer with no parts availableReplace the mixer
Corroded or cracked tap bodyReplace the tap

What affects the cost

  • The type of tap and whether parts are available.
  • How many taps are done in one visit.
  • Access: shower mixers behind tiles, tight vanities.
  • Isolation: whether there are working isolating valves.
  • New tapware: depends on the model.

You get a fixed price before any work starts.

Who's responsible?

  • You: taps, mixers and isolating valves in your home.
  • Owners corporation: shared pipes and common-area taps in an apartment building.
  • Sydney Water: the supply up to the meter.

Signs it's urgent and when it can wait

  • Call straight away if a tap won't turn off, or water is leaking into a wall or the unit below.
  • Call soon if a shower mixer leaks behind the tiles or a tap leaks at the base into the cupboard.
  • Book a time if a tap drips or is stiff.

A recent tap repair nearby

Here's a recent tap repair nearby in Maroubra, done on the same visit as a drain clear.

Leaking taps fixed during a drain clear, Maroubra (nearby)

The problem: a Maroubra home had leaking taps as well as slow drains.

What we did: we laid a mat to protect the floor, jetted the drains and floor wastes clear, and then repaired the leaking taps on the same visit.

The result: the taps shut off properly and the drains flow freely, all in one visit.

Floor protected during tap repairs near Eastlakes
Floor protected, Maroubra
Drain jetting on the same visit as tap repairs near Eastlakes
Drains cleared on the same visit

“Great plumber, fixed my leaking taps quickly and at a great price!”

Tom (Google review)

More local work is on our recent projects page.

Tap repairs across Eastlakes

  • The walk-up unit streets: worn tap cartridges and washer taps in 1960s and 70s blocks.
  • The brick house streets: older taps throughout, and rusty garden taps.
  • Around the Evans Avenue shops: newer apartments with mixers throughout.
  • Near The Lakes Golf Club: houses with laundry and garden taps that get heavy use.
  • Towards Rosebery and Daceyville: older homes with original galvanised pipe.

Kitchen taps

The kitchen tap is the hardest-working tap in most homes. It's used dozens of times a day, often pushed hard with wet or greasy hands. In Eastlakes units, kitchen mixers fitted during an update 10 to 20 years ago are now wearing out: the lever gets stiff, the spout drips, or water seeps out around the base and into the cupboard. Pull-out spray mixers have hoses that can crack and leak under the sink. We replace the cartridge, the O-rings or the hose, or replace the mixer if parts aren't available. If your stone benchtop has a single tap hole, we'll choose a replacement that fits it.

If you'd like filtered water at the kitchen sink, a filtered mixer can replace your existing tap without drilling a new hole. See water filters in Eastlakes.

Bathroom basin taps

Basin taps get gentler use but sit in a damp, soapy room. In older Eastlakes bathrooms, pillar taps with washers are common, and soap and limescale build up around the spindle and make them stiff. Vanity mixers in updated bathrooms usually have a smaller cartridge that wears in the same way as a kitchen mixer. A leak at the base of a basin tap often runs down into the vanity, where it swells the cabinet floor before anyone notices, so check inside the cupboard if you see water around the tap.

Shower taps and mixers

Shower taps are the ones most likely to cause hidden damage. The tap bodies sit inside the wall behind the tiles, and the spindles or cartridge seal against them. If a spindle O-ring fails, water can leak into the wall cavity every time the shower runs. Signs include damp skirting boards on the other side of the wall, loose or drummy tiles, mould along the grout, or a musty smell. A dripping shower rose usually means a worn washer or cartridge. In most cases, we replace spindles or cartridges from the front without removing tiles, using extension pieces if the tap body sits deep in the wall.

If your shower has old separate hot and cold taps, converting to quarter-turn spindles makes them easier to use and less likely to drip. If the tap bodies themselves are leaking inside the wall, they need replacing, which means opening the wall. We'll explain what we find and your options before any work starts. See leak detection in Eastlakes if you suspect a hidden leak.

Laundry taps

Laundry taps are often the oldest in the house. In Eastlakes brick houses and units, they're usually washer taps that have been left open for years to supply the washing machine. When you finally try to turn them off, they're stiff or seized, or they drip once you've moved them. We repair or replace laundry taps and fit new machine hoses. A modern washing machine tap with a single lever that turns both hot and cold off at once makes it easy to shut off the machine when you go away.

Garden and outdoor taps

Outdoor taps sit in the sun and weather, and the pipes that feed them often rise straight out of the ground. In older Eastlakes homes, those risers are often galvanised steel that has rusted at ground level. A garden tap that wobbles when you turn it, or leaks at the base, may have a rusted riser that's close to breaking. We replace the tap and the riser with copper and fix it securely to the wall or a post. A hose left connected and under pressure can also burst, so turn the tap off when you've finished watering.

Washer taps: repair them properly

The most common reason a washer tap keeps dripping is that only the washer gets changed. The washer presses onto a brass seat inside the tap body. Over the years, water and grit wear a groove into the seat. A new washer can't seal against a grooved seat, so the drip returns within weeks. A proper repair re-cuts the seat with a seat cutter so it's smooth and flat again, then fits a new washer, and replaces the O-rings on the spindle while the tap is open. Done properly, a washer tap repair lasts for years.

Converting to quarter-turn

If you like the look of your existing taps but would like them easier to use, ceramic disc conversion spindles turn traditional washer taps into quarter-turn taps. They replace the spindle inside the tap body, so the tap handles and bodies stay the same, with no change to the tiles or basin. Quarter-turn taps are easier on stiff fingers, shut off with a light touch, and drip far less than washer taps. They suit Eastlakes homes with older family members, and bathrooms where you'd rather not replace all the tapware.

Choosing new tapware

  • Match the holes: one, two or three holes in the basin, sink or benchtop.
  • Choose solid brass: it lasts longer than cheaper materials.
  • Pick a brand with local parts: it makes future repairs quicker.
  • Check the water rating: a good WELS rating saves water.
  • Think about the user: lever handles are easier for older hands and children.

Low flow at a tap

If one tap has low flow while others are fine, the cause is usually at that tap: a blocked aerator, a partly closed isolating valve, or a worn cartridge. Unscrewing and rinsing the aerator often fixes it. If every tap has low flow, the cause is further back: the meter valve, a pressure problem, or old galvanised pipes narrowing inside. We check from the tap back so we find the cause, not just the symptom.

Dripping taps and your water bill

A single dripping tap doesn't seem like much, but it runs every minute of every day. Over a year, a steady drip can add up to thousands of litres. In a Eastlakes brick house with its own meter, that adds to your bill. In a walk-up block on a shared meter, it's spread across everyone. A dripping hot tap is worse, because you're also paying to heat the water that goes down the drain. Fixing drips early also protects the tap: the longer a washer tap drips, the deeper the groove it wears in the seat.

Taps in units: protecting the home below

In a Eastlakes walk-up, a leak at the base of a basin tap or a shower mixer leaking inside the wall can reach the unit below. Water tracks along the slab or down through the wall and shows up as a stain on the neighbour's ceiling. If a neighbour tells you about a stain under your bathroom or kitchen, check the taps and the cupboard under each sink for damp, and look for loose tiles or damp grout around the shower. If you can't see the cause, call us and we'll find it. We'll give you a short note of what we found, which helps if the owners corporation or an insurer needs to know.

Taps that bang or shudder

If a pipe bangs when you turn a tap off quickly, that's water hammer: a pressure wave travelling through the pipes when the flow stops suddenly. It's most common with quarter-turn taps, mixers and washing machine valves that close fast. Loose pipes under the floor or in the wall make it louder. A tap that shudders or vibrates while running usually has a loose washer or worn spindle. We check the tap first, then the pipe clips and the water pressure. See water hammer.

Hot taps that run cold, or cold taps that run warm

If the hot water takes a long time to reach a tap, or a mixer gives warm water when set to cold, the cause can be a worn mixer cartridge letting hot and cold cross over, a faulty tempering valve, or a long pipe run from the hot water system. We check the mixer first, as a new cartridge often fixes it. If the problem is at the hot water system or the tempering valve, we'll explain what's needed. See hot water in Eastlakes.

Isolating valves under the sink

Most kitchen sinks and basins should have small isolating valves on the hot and cold pipes underneath. They let you turn off one tap without shutting off the whole home. In many older Eastlakes units and brick houses, these valves were never fitted, or they've seized after years of not being touched. When a tap needs repair and there's no working valve, the water has to go off at the meter. In an apartment building, that can mean finding the right meter in a bank near the front of the building. We replace seized valves, or fit new ones, as part of a tap repair. It makes the next repair quicker and gives you a way to stop a leak fast.

Getting ready for our visit

  • Take a photo of the tap and any brand name on it.
  • Clear the cupboard under the sink or vanity.
  • Know where your meter is, especially in an apartment building.
  • Tell us about access: stairs, parking and any building rules on work hours.
  • List every tap you'd like looked at, so we bring the right parts.

Why our tap repairs last

We repair taps the way they should be repaired: re-cut seats instead of just swapping washers, quality washers and O-rings, cartridges that match the original, and clean, lubricated spindles so the tap turns smoothly. We test every tap before we leave. Our labour is covered by a lifetime warranty, so if a tap we've repaired starts dripping again because of our work, we come back and fix it.

Taps for older hands

Turning a stiff washer tap hard enough to stop a drip is difficult for anyone with arthritis or weak grip, and many Eastlakes households include older family members. Lever mixers and quarter-turn taps need only a light push. A lever on the kitchen mixer, a quarter-turn conversion in the bathroom and a single-lever washing machine tap in the laundry make day-to-day life easier. Pairing new taps with a tempering valve on the hot water also reduces the risk of scalds at the bathroom taps. See tempering valve installation.

If you're not sure what kind of taps you have or what would suit, send us a photo. We'll tell you whether a repair, a conversion or a new tap makes the most sense, and give you a fixed price for each before any work starts.

Looking after your taps

  • Don't over-tighten washer taps; it wears the washer and seat faster.
  • Rinse aerators every few months.
  • Turn isolating valves off and on once a year so they don't seize.
  • Clean around spindles and bases with a mild cleaner.
  • Turn off garden taps fully after use.
  • Fix drips early, before they wear the seat badly.

What to expect on the day

We give you a time window and let you know when we're on the way. Most tap repairs are done in one visit with parts from the van. We protect your floor and benchtop, turn off the water, take the tap apart and show you the worn parts. Once it's repaired, we test it, check for leaks and make sure it turns smoothly. If we notice other taps close to needing attention, we'll let you know so you can decide whether to do them at the same time.

Tap words explained

  • Washer: the rubber disc that seals a traditional tap.
  • Seat: the brass ring inside the tap body that the washer closes on.
  • Spindle: the part that turns when you turn the handle.
  • Cartridge: the unit inside a mixer or quarter-turn tap that controls the water.
  • O-ring: a small rubber ring that seals around the spindle.
  • Aerator: the screen at the end of the spout that shapes the stream.
  • Isolating valve: a small valve under the sink that turns off water to one tap.

What happens when you call

1

Tell us what's going on

Call or send a quick form. A photo of the problem helps us come prepared. No call-out fee.

2

Options and a fixed price first

We find the cause, explain your options and give you a fixed price for each before any work starts.

3

Fixed, tested and backed

We do the work, test it, clean up, and back our workmanship with a lifetime labour warranty.

Jobs we finished recently

Toilet before repair in Chifley
Toilet before repair in Chifley
Toilet after repair in Chifley
Toilet after repair in Chifley

See more recent projects

Why Eastlakes homeowners call us

  • Based in Matraville, a few minutes from Eastlakes
  • Rated 5.0 from 110 Google reviews
  • Free quotes, with options and a fixed price before any work starts
  • Lifetime labour warranty on our workmanship
  • Licensed plumbers, drainers and gasfitters (Lic. 398171C)

Tap questions from Eastlakes homeowners

Why does my tap still drip after a new washer?

The seat is usually worn. We re-cut it as part of the repair.

Can you fix a dripping mixer?

Usually, with a new cartridge.

Can you repair a shower tap without removing tiles?

In most cases, yes, from the front.

Can washer taps be converted to quarter-turn?

Often, with ceramic disc spindles.

Why is my tap so stiff?

A worn spindle, a dry O-ring or a failing cartridge.

Why does my tap squeal?

Usually a loose washer or worn spindle.

Can you fix my garden tap?

Yes, and replace a rusted riser if needed.

Do I need to turn off all the water?

Only without a working isolating valve. We can fit one.

Can you supply new taps?

Yes, or fit ones you've bought.

How long does a tap repair take?

Most take under an hour.

Can you do several taps in one visit?

Yes, which saves another call-out.

What warranty do I get?

Our workmanship carries a lifetime labour warranty.

More plumbing in Eastlakes: our Eastlakes plumber page, taps and toilets, toilet repair and leak detection. Nearby: tap repair in Rosebery and Mascot. Guides: mixer tap leaking and ceramic disc vs washer taps.

Call 0401 758 373Free quote